C8051F326-GM Silicon Laboratories Inc, C8051F326-GM Datasheet - Page 106

• Manufacturer Part Number: C8051F326-GM
• Description: IC 8051 MCU FLASH 16K 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F326-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: UART/USART, USB
• Peripherals: POR
• Number Of I /o: 15
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• No. Of I/o's: 15
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 2
• Digital Ic Case Style: QFN
• Supply Voltage: RoHS Compliant
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F326
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1450 - ADAPTER PROGRAM TOOLSTICK F326336-1306 - KIT DEV FOR C8051F326/7
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1296-5

C8051F326/7
106
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
SSUEND SOPRDY
R/W
Bit7
USB Register Definition 12.17. E0CSR: USB0 Endpoint0 Control
SSUEND: Serviced Setup End
Write: Software should set this bit to ‘1’ after servicing a Setup End (bit SUEND) event.
Hardware clears the SUEND bit when software writes ‘1’ to SSUEND.
Read: This bit always reads ‘0’.
SOPRDY: Serviced OPRDY
Write: Software should write ‘1’ to this bit after servicing a received Endpoint0 packet. The
OPRDY bit will be cleared by a write of ‘1’ to SOPRDY.
Read: This bit always reads ‘0’.
SDSTL: Send Stall
Software can write ‘1’ to this bit to terminate the current transfer (due to an error condition,
unexpected transfer request, etc.). Hardware will clear this bit to ‘0’ when the STALL hand-
shake is transmitted.
SUEND: Setup End
Hardware sets this read-only bit to ‘1’ when a control transaction ends before software has
written ‘1’ to the DATAEND bit. Hardware clears this bit when software writes ‘1’ to SSU-
END.
DATAEND: Data End
Software should write ‘1’ to this bit:
1. When writing ‘1’ to INPRDY for the last outgoing data packet.
2. When writing ‘1’ to INPRDY for a zero-length data packet.
3. When writing ‘1’ to SOPRDY after servicing the last incoming data packet.
This bit is automatically cleared by hardware.
STSTL: Sent Stall
Hardware sets this bit to ‘1’ after transmitting a STALL handshake signal. This flag must be
cleared by software.
INPRDY: IN Packet Ready
Software should write ‘1’ to this bit after loading a data packet into the Endpoint0 FIFO for
transmit. Hardware clears this bit and generates an interrupt under either of the following
conditions:
1. The packet is transmitted.
2. The packet is overwritten by an incoming SETUP packet.
3. The packet is overwritten by an incoming OUT packet.
OPRDY: OUT Packet Ready
Hardware sets this read-only bit and generates an interrupt when a data packet has been
received. This bit is cleared only when software writes ‘1’ to the SOPRDY bit.
R/W
Bit6
SDSTL
R/W
Bit5
SUEND DATAEND
Bit4
R
Rev. 1.1
R/W
Bit3
STSTL
R/W
Bit2
INPRDY
R/W
Bit1
OPRDY
Bit0
R
USB Address:
00000000
Reset Value
0x11