C8051F326-GM Silicon Laboratories Inc, C8051F326-GM Datasheet - Page 31

• Manufacturer Part Number: C8051F326-GM
• Description: IC 8051 MCU FLASH 16K 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F326-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: UART/USART, USB
• Peripherals: POR
• Number Of I /o: 15
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• No. Of I/o's: 15
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 2
• Digital Ic Case Style: QFN
• Supply Voltage: RoHS Compliant
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F326
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1450 - ADAPTER PROGRAM TOOLSTICK F326336-1306 - KIT DEV FOR C8051F326/7
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1296-5

5.
C8051F326/7 devices include a voltage regulator (REG0). When enabled, the REG0 output appears on
the VDD pin and can be used to power external devices. REG0 can be enabled/disabled by software using
bit REGEN in register REG0CN. See Table 5.1 for REG0 electrical characteristics.
The voltage regulator is enabled on reset. When the device is self-powered from a 3V supply net, the reg-
ulator may be disabled in order to save power. Important Note: If the voltage at the regulator input
(REGIN) is greater than the Core Supply Voltage (VDD), the voltage regulator should not be dis-
abled. Otherwise, permanent damage to the device may occur.
Note that the VBUS signal must be connected to the VBUS pin when using the device in a USB network.
The VBUS signal should only be connected to the REGIN pin when operating the device as a bus-powered
function. REG0 configuration options are shown in Figure 5.1 - Figure 5.4.
5.1.
REG0 offers a low power mode intended for use when the device is in suspend mode. In this low power
mode, the REG0 output remains as specified; however the REG0 dynamic performance (response time) is
degraded. See Table 5.1 for normal and low power mode supply current specifications. The REG0 mode
selection is controlled via the REGMOD bit in register REG0CN.
5.2.
When the USB Function Controller is used (see section Section “12. Universal Serial Bus Controller
(USB0)” on page 87), the VBUS signal should be connected to the VBUS pin. The VBSTAT bit (register
REG0CN) indicates the current logic level of the VBUS signal. If enabled, a VBUS interrupt will be gener-
ated when the VBUS signal matches the polarity selected by the VBPOL bit in register REG0CN. The
VBUS interrupt is level-sensitive, and has no associated interrupt pending flag. The VBUS interrupt will be
active as long as the VBUS signal matches the polarity selected by VBPOL. See Table 5.1 for VBUS input
parameters.
Important Note: When USB is selected as a reset source, a system reset will be generated when the
VBUS signal matches the polarity selected by the VBPOL bit. See Section “7. Reset Sources” on page 57
for details on selecting USB as a reset source.
Table 5.1. Voltage Regulator Electrical Specifications
V
Input Voltage Range
Output Voltage
VBUS Detection Input Threshold
Bias Current
Dropout Voltage (V
*Note: The minimum input voltage is 2.70 V or V
DD
= 3.0 V; –40 to +85 °C unless otherwise specified.
Voltage Regulator (REG0)
Regulator Mode Selection
VBUS Detection
Parameter
DO
)*
Output Current = 1 to 100 mA
Normal Mode (REGMOD = ‘0’)
Low Power Mode (REGMOD = ‘1’)
IDD = 1 to 100 mA
DD
Conditions
+ V
Rev. 1.1
DO
(max load), whichever is greater.
Min
2.7
3.0
1.0
—
—
—
C8051F326/7
Typ
3.3
1.8
75
41
—
1
Max
5.25
111
3.6
2.9
61
—
mV/mA
Units
µA
V
V
V
31