C8051F326-GM Silicon Laboratories Inc, C8051F326-GM Datasheet - Page 128

• Manufacturer Part Number: C8051F326-GM
• Description: IC 8051 MCU FLASH 16K 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F326-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: UART/USART, USB
• Peripherals: POR
• Number Of I /o: 15
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• No. Of I/o's: 15
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 2
• Digital Ic Case Style: QFN
• Supply Voltage: RoHS Compliant
• Package: 28QFN EP
• Device Core: 8051
• Family Name: C8051F326
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1450 - ADAPTER PROGRAM TOOLSTICK F326336-1306 - KIT DEV FOR C8051F326/7
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1296-5

C8051F326/7
14.1.1. Mode 0: 13-bit Timer
Timer 0 and Timer 1 operate as 13-bit timers in Mode 0. The following describes the configuration and
operation of Timer 0. However, both timers operate identically, and Timer 1 is configured in the same man-
ner as described for Timer 0.
The TH0 register holds the eight MSBs of the 13-bit timer. TL0 holds the five LSBs in bit positions TL0.4-
TL0.0. The three upper bits of TL0 (TL0.7-TL0.5) are indeterminate and should be masked out or ignored
when reading. As the 13-bit timer register increments and overflows from 0x1FFF (all ones) to 0x0000, the
timer overflow flag TF0 (TCON.5) is set and an interrupt will occur if Timer 0 interrupts are enabled.
Setting the TR0 bit (TCON.4) enables the timer when either GATE0 (TMOD.3) is logic 0 or GATE0 is logic
1 and the input signal /INT0 is active. Setting GATE0 to logic 1 allows the timer to be controlled by the
external input signal /INT0, facilitating pulse width measurements. When GATE0 is set to logic 1, the /INT0
input pin is P0.2.
See Table 6.4 on page 49 for detailed information on how GATE0 affects /INT0 functionality.
Setting TR0 does not force the timer to reset. The timer registers should be loaded with the desired initial
value before the timer is enabled. TL1 and TH1 form the 13-bit register for Timer 1 in the same manner as
described above for TL0 and TH0. Timer 1 is configured and controlled using the relevant TCON and
TMOD bits just as with Timer 0. The input signal /INT1 is used with Timer 1. See Section “6.3.2. External
Interrupts” on page 49 for a complete description of /INT0 and /INT1.
128
G
A
T
E
1
C
T
1
/
M
T
1
1
TMOD
M
T
1
0
G
A
T
E
0
C
T
0
/
M
T
0
1
M
T
0
0
Pre-scaled Clock
SYSCLK
TR0
X = Don't Care
GATE0
0
1
1
1
/INT0
Figure 14.1. T0 Mode 0 Block Diagram
CKCON
Table 14.2. Timer 0 Operation
GATE0
M
T
1
TR0
T
M
0
1
0
X
0
1
1
S
C
A
1
C
S
A
0
Rev. 1.1
0 (P0.2 High)
1 (P0.2 Low)
/INT0
X
X
TCLK
(5 bits)
TL0
Disabled
Disabled
Enabled
Enabled
Timer
(8 bits)
TH0
TR1
TR0
TF1
TF0
IE1
IE0
IT1
IT0
Interrupt