C8051F901-GU Silicon Laboratories Inc, C8051F901-GU Datasheet - Page 235

• Manufacturer Part Number: C8051F901-GU
• Description: IC MCU 8BIT 8KB FLASH 24QSOP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F901-GU

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 24-QSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 15x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Ram Size: 768 B
• Interface Type: UART
• Maximum Clock Frequency: 25 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F912DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 24QSOP
• Device Core: 8051
• Family Name: C8051F90x
• Maximum Speed: 25 MHz
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1847-5

ARBLOST
TXMODE
MASTER
ACKRQ
STO
ACK
STA
Bit
SI
• A START is generated.
• START is generated.
• SMB0DAT is written before the start of an
• A START followed by an address byte is
• A STOP is detected while addressed as a
• Arbitration is lost due to a detected STOP.
• A byte has been received and an ACK
• A repeated START is detected as a MASTER
• SCL is sensed low while attempting to gener-
• SDA is sensed low while transmitting a 1
• The incoming ACK value is low 
• A START has been generated.
• Lost arbitration.
• A byte has been transmitted and an
• A byte has been received.
• A START or repeated START followed by a
• A STOP has been received.
SMBus frame.
received.
slave.
response value is needed (only when hard-
ware ACK is not enabled).
when STA is low (unwanted repeated START).
ate a STOP or repeated START condition.
(excluding ACK bits).
(ACKNOWLEDGE).
ACK/NACK received.
slave address + R/W has been received.
Table 22.3. Sources for Hardware Changes to SMB0CN
Set by Hardware When:
Rev. 1.0
C8051F91x-C8051F90x
• A STOP is generated.
• Arbitration is lost.
• A START is detected.
• Arbitration is lost.
• SMB0DAT is not written before the
• Must be cleared by software.
• A pending STOP is generated.
• After each ACK cycle.
• Each time SI is cleared.
• The incoming ACK value is high (NOT
• Must be cleared by software.
start of an SMBus frame.
ACKNOWLEDGE).
Cleared by Hardware When:
235