C8051F901-GU Silicon Laboratories Inc, C8051F901-GU Datasheet - Page 288

• Manufacturer Part Number: C8051F901-GU
• Description: IC MCU 8BIT 8KB FLASH 24QSOP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F9xxr

Specifications of C8051F901-GU

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 24-QSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 15x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F9x
• Core: 8051
• Data Ram Size: 768 B
• Interface Type: UART
• Maximum Clock Frequency: 25 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F912DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Package: 24QSOP
• Device Core: 8051
• Family Name: C8051F90x
• Maximum Speed: 25 MHz
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1847-5

C8051F91x-C8051F90x
25.3.3. Comparator 1/External Oscillator Capture Mode
The Capture Mode in Timer 3 allows either Comparator 1 or the external oscillator period to be measured
against the system clock or the system clock divided by 12. Comparator 1 and the external oscillator
period can also be compared against each other.
Setting TF3CEN to 1 enables the Comparator 1/External Oscillator Capture Mode for Timer 3. In this
mode, T3SPLIT should be set to 0, as the full 16-bit timer is used.
When Capture Mode is enabled, a capture event will be generated either every Comparator 1 rising edge
or every 8 external clock cycles, depending on the T3XCLK1 setting. When the capture event occurs, the
contents of Timer 3 (TMR3H:TMR3L) are loaded into the Timer 3 reload registers (TMR3RLH:TMR3RLL)
and the TF3H flag is set (triggering an interrupt if Timer 3 interrupts are enabled). By recording the differ-
ence between two successive timer capture values, the Comparator 1 or external clock period can be
determined with respect to the Timer 3 clock. The Timer 3 clock should be much faster than the capture
clock to achieve an accurate reading.
For example, if T3ML = 1b, T3XCLK1 = 0b, and TF3CEN = 1b, Timer 3 will clock every SYSCLK and cap-
ture every Comparator 1 rising edge. If SYSCLK is 24.5 MHz and the difference between two successive
captures is 350 counts, then the Comparator 1 period is:
350 x (1 / 24.5 MHz) = 14.2 µs.
This mode allows software to determine the exact frequency of the external oscillator in C and RC mode or
the time between consecutive Comparator 0 rising edges, which is useful for detecting changes in the
capacitance of a Touch Sense Switch.
288
E xternal C lock / 8
E xtern al C lock / 8
C om parato r 1
S Y S C LK / 1 2
C om p arator 1
S Y S C LK
T 3X C LK [1:0]
T 3X C LK 1
X 0
01
11
0
1
Figure 25.9. Timer 3 Capture Mode Block Diagram
M
H
T
3
M
0
1
T
3
L
C K C O N
M
T
2
H
M
T
2
L
M
T
1
T F 3 C E N
M
T
0
S
C
A
1
T R 3
S
C
A
0
Rev. 1.0
C apture
T C LK
T M R 3R L L T M R 3 R LH
T M R 3 L
T M R 3H
T 3 X C L K 1
T 3 X C L K 0
T F 3C E N
T 3S P LIT
T F 3 L E N
T F 3H
T F 3L
T R 3
Inte rrupt