ATTINY84-15MZ Atmel, ATTINY84-15MZ Datasheet - Page 53

• Manufacturer Part Number: ATTINY84-15MZ
• Description: MCU AVR 8K FLASH 15MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY84-15MZ

• Package / Case: 20-QFN Exposed Pad
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 12
• Eeprom Size: 512 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Program Memory Size: 8KB (8K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, UART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.2.3
11.2.4
7701D–AVR–09/10
GIFR – General Interrupt Flag Register
PCMSK1 – Pin Change Mask Register 1
• Bit 4– PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set and the I-bit in the Status Register (SREG) is set, pin change inter-
rupt 0 is enabled. Any change on any enabled PCINT7..0 pin will cause an interrupt. The
corresponding interrupt of pin change interrupt request is executed from the PCI0 interrupt
vector. PCINT7..0 pins are enabled individually by the PCMSK0 register.
• Bits 7, 3..0 – Res: Reserved Bits
These bits are reserved bits in the ATtiny24/44/84 and will always read as zero.
• Bit 6 – INTF0: External Interrupt Flag 0
When an edge or logic change on the INT0 pin triggers an interrupt request, INTF0 becomes
set (logical one). If the I-bit in SREG and the INT0 bit in GIMSK are set (one), the MCU will
jump to the corresponding Interrupt Vector. The flag is cleared when the interrupt routine is
executed. Alternatively, the flag can be cleared by writing a logical one to it. This flag is always
cleared when INT0 is configured as a level interrupt.
• Bit 5 – PCIF1: Pin Change Interrupt Flag 1
When a logic change on any PCINT11..8 pin triggers an interrupt request, PCIF1 becomes set
(logical one). If the I-bit in SREG and the PCIE1 bit in GIMSK are set (one), the MCU will jump
to the corresponding Interrupt Vector. The flag is cleared when the interrupt routine is exe-
cuted. Alternatively, the flag can be cleared by writing a logical one to it.
• Bit 4– PCIF0: Pin Change Interrupt Flag 0
When a logic change on any PCINT7..0 pin triggers an interrupt request, PCIF becomes set
(logical one). If the I-bit in SREG and the PCIE0 bit in GIMSK are set (one), the MCU will jump
to the corresponding Interrupt Vector. The flag is cleared when the interrupt routine is exe-
cuted. Alternatively, the flag can be cleared by writing a logical one to it.
• Bits 7, 4– Res: Reserved Bits
These bits are reserved bits in the Atmel
Bit
0x3A (0x5A
Read/Write
Initial Value
Bit
0x20 (0x40)
Read/Write
Initial Value
R
7
–
0
R
7
–
0
INTF0
R
6
–
0
R/W
6
0
Atmel ATtiny24/44/84 [Preliminary]
PCIF1
R
0
5
–
R/W
5
0
®
R
4
–
0
PCIF0
ATtiny24/44/84 and will always read as zero.
R/W
4
0
PCINT11
R/W
3
0
R
3
–
0
PCINT10
R/W
2
0
R
2
–
0
PCINT9
R/W
1
0
R
1
–
0
PCINT8
R/W
0
0
0
–
R
0
PCMSK1
GIFR
53