AT89C51CC01UA-SLSUM Atmel, AT89C51CC01UA-SLSUM Datasheet - Page 4

• Manufacturer Part Number: AT89C51CC01UA-SLSUM
• Description: IC 8051 MCU FLASH 32K 44-PLCC
• Manufacturer: Atmel
• Series: AT89C CANr

Specifications of AT89C51CC01UA-SLSUM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-PLCC
• Package: 44PLCC
• Device Core: 8051
• Family Name: 89C
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 34
• Interface Type: CAN/UART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Processor Series: AT89x
• Core: 8051
• Data Ram Size: 1280 B
• Maximum Clock Frequency: 40 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: CANADAPT28
• Minimum Operating Temperature: - 40 C
• Cpu Family: AT89
• Device Core Size: 8b
• Frequency (max): 40MHz
• Total Internal Ram Size: 1.25KB
• # I/os (max): 34
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PLCC
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: AT89C51CC01UASLSUM

I/O Configurations
Port 1, Port 3 and Port 4
Port 0 and Port 2
4
A/T89C51CC01
Each Port SFR operates via type-D latches, as illustrated in Figure 1 for Ports 3 and 4. A
CPU "write to latch" signal initiates transfer of internal bus data into the type-D latch. A
CPU "read latch" signal transfers the latched Q output onto the internal bus. Similarly, a
"read pin" signal transfers the logical level of the Port pin. Some Port data instructions
activate the "read latch" signal while others activate the "read pin" signal. Latch instruc-
tions are referred to as Read-Modify-Write instructions. Each I/O line may be
independently programmed as input or output.
Figure 1 shows the structure of Ports 1 and 3, which have internal pull-ups. An external
source can pull the pin low. Each Port pin can be configured either for general-purpose
I/O or for its alternate input output function.
To use a pin for general-purpose output, set or clear the corresponding bit in the Px reg-
ister (x = 1,3 or 4). To use a pin for general-purpose input, set the bit in the Px register.
This turns off the output FET drive.
To configure a pin for its alternate function, set the bit in the Px register. When the latch
is set, the "alternate output function" signal controls the output level (see Figure 1). The
operation of Ports 1, 3 and 4 is discussed further in the "quasi-Bidirectional Port Opera-
tion" section.
Figure 1. Port 1, Port 3 and Port 4 Structure
Note:
Ports 0 and 2 are used for general-purpose I/O or as the external address/data bus. Port
0, shown in Figure 3, differs from the other Ports in not having internal pull-ups. Figure 3
shows the structure of Port 2. An external source can pull a Port 2 pin low.
To use a pin for general-purpose output, set or clear the corresponding bit in the Px reg-
ister (x = 0 or 2). To use a pin for general-purpose input, set the bit in the Px register to
turn off the output driver FET.
READ
LATCH
INTERNAL
BUS
WRITE
TO
LATCH
The internal pull-up can be disabled on P1 when analog function is selected.
READ
PIN
D
CL
LATCH
P1.X
P3.X
P4.X
Q
ALTERNATE
OUTPUT
FUNCTION
ALTERNATE
INPUT
FUNCTION
VCC
INTERNAL
PULL-UP (1)
4129N–CAN–03/08
P1.x
P3.x
P4.x