P89LPC931A1FDH,512 NXP Semiconductors, P89LPC931A1FDH,512 Datasheet - Page 37

• Manufacturer Part Number: P89LPC931A1FDH,512
• Description: IC 80C51 MCU FLASH 8K 28-TSSOP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC931A1FDH,512

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 28-TSSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 3
• Operating Supply Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-1758 - BOARD EVAL FOR LPC93X MCU FAMILY
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935288634512

NXP Semiconductors
P89LPC9301_931A1
Product data sheet
Fig 14. Watchdog timer in Watchdog mode (WDTE = 1)
watchdog
oscillator
(1) Watchdog reset can also be caused by an invalid feed sequence, or by writing to WDCON not immediately followed by a feed
PCLK
sequence.
7.28.1 Software reset
7.28.2 Dual data pointers
7.29.1 General description
0
1
7.28 Additional features
7.29 Flash program memory
MOV WFEED1, #0A5H
MOV WFEED2, #05AH
oscillator
crystal
The SRST bit in AUXR1 gives software the opportunity to reset the processor completely,
as if an external reset or watchdog reset had occurred. Care should be taken when writing
to AUXR1 to avoid accidental software resets.
The dual Data Pointers (DPTR) provides two different Data Pointers to specify the
address used with certain instructions. The DPS bit in the AUXR1 register selects one of
the two Data Pointers. Bit 2 of AUXR1 is permanently wired as a logic 0 so that the DPS
bit may be toggled (thereby switching Data Pointers) simply by incrementing the AUXR1
register, without the possibility of inadvertently altering other bits in the register.
The P89LPC9301/931A1 flash memory provides in-circuit electrical erasure and
programming. The flash can be erased, read, and written as bytes. The Sector and Page
Erase functions can erase any flash sector (1 kB) or page (64 bytes). The Chip Erase
operation will erase the entire program memory. ICP using standard commercial
programmers is available. In addition, IAP and byte-erase allows code memory to be used
for non-volatile data storage. On-chip erase and write timing generation contribute to a
user-friendly programming interface. The P89LPC9301/931A1 flash reliably stores
memory contents even after 100,000 erase and program cycles. The cell is designed to
XTALWD
0
1
WDCON (A7H)
÷32
All information provided in this document is subject to legal disclaimers.
PRE2
Rev. 2 — 29 November 2010
PRESCALER
8-bit microcontroller with accelerated two-clock 80C51 core
PRE1
PRE0
SHADOW REGISTER
-
P89LPC9301/931A1
-
8-BIT DOWN
WDL (C1H)
COUNTER
WDRUN
WDTOF
© NXP B.V. 2010. All rights reserved.
WDCLK
002aae015
reset
37 of 66
(1)