ST72F63BK4M1 STMicroelectronics, ST72F63BK4M1 Datasheet - Page 24

• Manufacturer Part Number: ST72F63BK4M1
• Description: IC MCU 8BIT LS 16K 34-SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F63BK4M1

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI, USB
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 19
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 34-SOIC (7.5mm Width)
• Processor Series: ST72F6x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SCI, USB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 27
• Number Of Timers: 2 x 16 bit
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7MDTU3-EPB/US, ST72F63B-SK/RAIS, ST7MDTU3-EMU3, STX-RLINK
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8 bit
• For Use With: 497-5521 - EVAL BOARD LOW SPEED USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2115-5

Flash program memory
4
4.1
4.2
4.3
24/186
Flash program memory
Introduction
The ST7 dual voltage High Density Flash (HDFlash) is a non-volatile memory that can be
electrically erased as a single block or by individual sectors and programmed on a byte-by-
byte basis using an external V
The HDFlash devices can be programmed and erased off-board (plugged in a programming
tool) or on-board using ICP (in-circuit programming) or IAP (in-application programming).
The array matrix organization allows each sector to be erased and reprogrammed without
affecting other sectors.
Main features
●
●
●
●
Structure
The Flash memory is organized in sectors and can be used for both code and data storage.
Depending on the overall Flash memory size in the microcontroller device, there are up to
three user sectors (see
avoid unnecessary erasing of the whole Flash memory when only a partial erasing is
required.
The first two sectors have a fixed size of 4 Kbytes (see
upper part of the ST7 addressing space so the reset and interrupt vectors are located in
Sector 0 (F000h-FFFFh).
Table 7.
3 Flash programming modes:
–
–
–
ICT (in-circuit testing) for downloading and executing user application test patterns in
RAM
Readout protection
Register access security system (RASS) to prevent accidental programming or erasing
Insertion in a programming tool. In this mode, all sectors including option bytes
can be programmed or erased.
ICP (in-circuit programming). In this mode, all sectors including option bytes can
be programmed or erased without removing the device from the application board.
IAP (in-application programming). In this mode, all sectors except Sector 0, can be
programmed or erased without removing the device from the application board
and while the application is running.
Sectors available in Flash devices
Flash size (Kbytes)
> 8
4
8
Table
7). Each of these sectors can be erased independently to
PP
Doc ID 7516 Rev 8
supply.
Figure
Available sectors
Sectors 0,1, 2
8). They are mapped in the
Sectors 0,1
Sector 0
ST7263Bxx