ATMEGA161-8PI Atmel, ATMEGA161-8PI Datasheet - Page 131

• Manufacturer Part Number: ATMEGA161-8PI
• Description: IC AVR MCU 16K 8MHZ IND 40-DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA161-8PI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Data Converters: -
• Other names: ATMEGA1618PI

DC Characteristics
T
Notes:
1228D–AVR–02/07
A
Symbol
V
V
V
V
V
V
V
I
I
RRST
R
I
V
I
t
IL
IH
CC
ACLK
ACPD
IL
IL1
IH
IH1
IH2
OL
OH
ACIO
I/O
= -40°C to 85°C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. Although each I/O port can sink more than the test conditions (20 mA at V
4. Although each I/O port can source more than the test conditions (3 mA at V
conditions (non-transient), the following must be observed:
1] The sum of all I
2] The sum of all I
3] The sum of all I
If I
than the listed test condition.
conditions (non-transient), the following must be observed:
1] The sum of all I
2] The sum of all I
3] The sum of all I
Parameter
Input Low Voltage
Input Low Voltage
Input High Voltage
Input High Voltage
Input High Voltage
Output Low Voltage
(Ports A,B,C,D)
Output High Voltage
(Ports A,B,C,D)
Input Leakage
Current I/O pin
Input Leakage
Current I/O pin
Reset Pull-up Resistor
I/O Pin Pull-up Resistor
Power Supply Current
Power-down mode
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
OL
exceeds the test condition, V
CC
= 2.7V to 5.5V (unless otherwise noted)
OL
OL
OL
OH
OH
OH
(5)
, for all ports, should not exceed 200 mA.
, for ports B0 - B7, D0 - D7 and XTAL2, should not exceed 100 mA.
, for ports A0 - A7, ALE, OC1B and C0 - C7 should not exceed 100 mA.
(3)
, for all ports, should not exceed 200 mA.
, for ports B0 - B7, D0 - D7 and XTAL2, should not exceed 100 mA.
, for ports A0 - A7, ALE, OC1B and C0 - C7 should not exceed 100 mA.
(4)
(Except XTAL1)
(XTAL1)
(XTAL1)
(RESET)
I
4 MHz
Idle mode V
Condition
(Except XTAL1, RESET)
I
I
I
V
(absolute value)
V
(absolute value)
Active mode, V
4 MHz
WDT enabled, V
WDT disabled, V
V
V
V
V
V
V
OL
OL
OH
OH
CC
CC
CC
in
CC
in
CC
CC
= 20 mA, V
= 10 mA, V
= V
= V
= -3 mA, V
= -1.5 mA, V
= 5.5V, pin low
= 5.5V, pin high
= 5V
= 5V
= 2.7V
= 4.0V
OL
CC
CC
may exceed the related specification. Pins are not guaranteed to sink current greater
/2
/2
CC
CC
CC
CC
= 3V,
CC
CC
CC
CC
= 5V
= 5V
= 3V
= 3V,
= 3V
= 3V
= 3V
(1)(2)(3)(4)(5)
0.6 V
0.8 V
0.9 V
Min
-0.5
-0.5
100
4.2
2.3
-50
35
CC
CC
CC
(2)
(2)
(2)
CC
CC
= 5V, 10 mA at V
= 5V, 1.5 mA at V
Typ
750
500
<1
9
ATmega161(L)
0.3
0.2
V
V
V
CC
CC
CC
CC
CC
Max
15.0
980
500
120
0.6
0.5
8.0
3.0
1.2
2.0
40
50
V
V
+ 0.5
+ 0.5
+ 0.5
= 3V) under steady-state
= 3V) under steady-state
CC
CC
(1)
(1)
Units
mA
mA
mV
kΩ
kΩ
µA
nA
µA
µA
nA
ns
V
V
V
V
V
V
V
V
V
131