JN5139-Z01-V NXP Semiconductors, JN5139-Z01-V Datasheet - Page 64

• Manufacturer Part Number: JN5139-Z01-V
• Description: IC MCU ZIGBEE 32BIT 2.4G 56QFN
• Manufacturer: NXP Semiconductors
• Series: JN5139-Z01Rxr

Specifications of JN5139-Z01-V

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: General Purpose
• Power - Output: 3dBm
• Sensitivity: -97dBm
• Voltage - Supply: 2.2 V ~ 3.6 V
• Current - Receiving: 34mA
• Current - Transmitting: 34mA
• Data Interface: PCB, Surface Mount
• Memory Size: 96kB RAM, 192kB ROM
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 56-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Rate - Maximum: -
• Other names: 616-1034-2; 935293943515; JN5139-Z01-AI; JN5139-Z01-V; JN5139-Z01R1-ARV; JN5139-Z01R1V

17.3.13.3 Radio parameters: 2.2-3.6V, +85ºC
64
EVM [offset]
Transmit Power
Spectral Density
Receive sensitivity
Maximum input signal
Adjacent channel
rejection
-1 channel / +1 channel
Alternate channel
rejection
Other in band rejection
2.4 to 2.4835 GHz,
excluding adj channels
Out of band rejection
Spurious emissions
(RX)
Intermodulation
protection
RSSI linearity
Transmit power
Transmit power (boost)
Output power control
range
Spurious emissions
(TX)
Parameter
Parameter
Min
Min
-4
Typical
Typical
20 [6.2]
27 / 35
Transmitter Characteristics
-32.0
+0.6
-1.3
-36
Receiver Characteristics
-94
-69
-54
-69
-44
42
50
47
51
JN-DS-JN5139 1v9
Max
Max
+10
-20
-66
-51
-66
-41
30
+4
Unit
dBc
dBm
dBm
dBm
dBm
dBm
dBm
Unit
%
dB
dB
dB
dB
dB
dB
dB
per 802.15.4, section 6.5.3.1
At maximum output power
At greater than 3.5MHz offset, as
Nominal for 1% PER, as per
802.15.4 section 6.5.3.3
For 1% PER, measured as
sensitivity
For 1% PER with wanted signal
3dB above sensitivity, (Note1)
For 1% PER with wanted signal
3dB above sensitivity, (Note1)
For 1% PER with wanted signal
3dB above sensitivity, (Note1)
For 1% PER with wanted signal
3dB above sensitivity. All
frequencies except wanted/2
which is 4dB lower (Note1)
Measured conducted into 50ohms
30MHz to 1GHz
1GHz to 12GHz
For 1% PER at with wanted
signal 3dB above sensitivity.
Modulated Interferers at 2 & 4
channel separation. (Note1)
-95 to -10dBm
In five steps of 6dB (Note2)
Measured conducted into 50ohms
30MHz to 1GHz,
1GHz to12.5GHz,
© NXP Laboratories UK 2010
Notes
Notes