AMIS-52150-XTD ON Semiconductor, AMIS-52150-XTD Datasheet - Page 14

• Manufacturer Part Number: AMIS-52150-XTD
• Description: TXRX RF SUB 1GHZ CDR 20-SSOP
• Manufacturer: ON Semiconductor

Specifications of AMIS-52150-XTD

• Frequency: 300Mhz ~ 768MHz
• Data Rate - Maximum: 16kbps
• Modulation Or Protocol: ASK, OOK
• Applications: Wireless Modules
• Power - Output: 12dBm
• Sensitivity: -117dBm
• Voltage - Supply: 2.3 V ~ 3.6 V
• Current - Receiving: 7.5mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: 0°C ~ 50°C
• Package / Case: 20-SSOP
• Ic Interface Type: I2C
• No. Of Tx Buffers: 1
• No. Of Rx Buffers: 1
• No. Of Filters: 1
• No. Of Interrupts: 1
• Supply Voltage Range: 2.3V To 3.6V
• Digital Ic Case Style: SSOP
• No. Of Pins: 20
• Rohs Compliant: No
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Modulation Type: ASK/OOK
• Operating Supply Voltage (min): 2.3V
• Operating Supply Voltage (typ): 3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 766-1020

AMIS-52150
Table 23: Output Impedance Characteristics
9.3 Sniff Mode
Applications based on low power consumption require Sniff Mode
the crystal oscillator during programmable, regular time intervals. At the end of each time interval, the receiver wakes up and sniffs for
the incoming RF energy. If energy is detected, the receiver transitions to the full receive mode and starts data recovery from the RF
carrier. If energy is not detected, the receiver returns to the low power or “sleep” state. Sniff Mode
“sleep” time as well as multiple delay sequences can be fully programmed. Table 24 lists the Sniff Mode
Typical timing waveforms for operation in Sniff Mode
Table 24: Sniff Function Control Registers
Specification
Output impedance
Output power
Harmonics
Frequency range
Modulation
On/off ratio
Control Registers Associated with the Sniff Function
Register (HEX)
0x0b
0x0c
0x0d
0x13
0x16
0x18
0x19
0x1a
0x1b
TM
Name
SNIFF Threshold
WAKE on RSSI
SNIFF TIMER RES
DATA FILTER
IRQ DELAY
RSSI DELAY
SNIFF TIMER
OFFSET DWELL
DATA FILTER PRE-DIVIDER
Settings
RFPWR 0x00
RFPWR 0xff
TX output
Conditions
Resistance
Capacitance
Ext. circuit
Target
Quick Start
Full range
Rev. 7 | Page 14 of 25 | www.onsemi.com
TM
Bits
Figure 8: Transmit Waveforms
are shown in Figure 9 and Figure 10.
All
All
All
All
All
All
All
5
3
Min.
402
350
300
11
States
0
1
0
1
TM
ASK/OOK
operation of the AMIS-52150. This mode turns off the receiver and
Typ.
-26
-35
22
12
70
Comments
Reference level for detected RF
Do not wake on RSSI
Wake on RSSI > threshold
Resolution is set to 0.5mS per step
Resolution is set to 64mS per step
Delay from RX wakeup to data sampled
Time I
Delay from wakeup to RSSI being checked
Time that receiver is off in Sniff Mode
Time allowing receiver to power up (typically >40uS)
Delay from data detection to pre-clock output
3
2
C and TX/RX are active to indicate a wakeup
Max.
405
448
768
13
pFarads
Units
dBm
dBm
dBm
MHz
MHz
MHz
dBm
Ω
TM
TM
operation is programmable; the
control registers.