ATMEGA2560R231-AU Atmel, ATMEGA2560R231-AU Datasheet - Page 45

BUNDLE ATMEGA2560/RF231 TQFP

ATMEGA2560R231-AU

Manufacturer Part Number
ATMEGA2560R231-AU
Description
BUNDLE ATMEGA2560/RF231 TQFP
Manufacturer
Atmel
Datasheet

Specifications of ATMEGA2560R231-AU

Frequency
2.4GHz
Modulation Or Protocol
802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
Data Interface
PCB, Surface Mount
Memory Size
256kB Flash, 4kB EEPROM, 8kB RAM
Antenna Connector
PCB, Surface Mount
Package / Case
100-TFBGA
Processor Series
ATMEGA256x
Core
AVR8
Data Bus Width
8 bit
Program Memory Type
Flash
Program Memory Size
256 KB
Data Ram Size
8 KB
Development Tools By Supplier
ATAVRRZ541, ATAVRRAVEN, ATAVRRZRAVEN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Power - Output
-
Operating Temperature
-
Applications
-
Sensitivity
-
Data Rate - Maximum
-
Current - Transmitting
-
Current - Receiving
-
Lead Free Status / Rohs Status
 Details
9.6
2549M–AVR–09/10
Low Frequency Crystal Oscillator
Table 9-6.
Notes:
The device can utilize a 32.768 kHz watch crystal as clock source by a dedicated Low Fre-
quency Crystal Oscillator. The crystal should be connected as shown in
When this Oscillator is selected, start-up times are determined by the SUT Fuses and CKSEL0
as shown in
The Low-Frequency Crystal Oscillator provides an internal load capacitance, see
each XTAL/TOSC pin.
Table 9-7.
Device
Ceramic resonator, slowly
Ceramic resonator, slowly
ATmega640/1280/1281/2560
Ceramic resonator, BOD
Crystal Oscillator, slowly
Ceramic resonator, fast
Ceramic resonator, fast
Crystal Oscillator, BOD
Crystal Oscillator, fast
Oscillator Source /
Power Conditions
rising power
rising power
rising power
rising power
rising power
rising power
1. These options should only be used when not operating close to the maximum frequency of the
2. These options are intended for use with ceramic resonators and will ensure frequency stability
enabled
enabled
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals.
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
/2561
Table 9-8 on page
Start-up Times for the Full Swing Crystal Oscillator Clock Selection
Capacitance for Low Frequency Oscillator
32 kHz oscillator
Start-up Time from
Power-down and
46.
ATmega640/1280/1281/2560/2561
Power-save
System Osc.
Timer Osc.
16K CK
16K CK
16K CK
258 CK
258 CK
1K CK
1K CK
1K CK
Cap (Xtal1/Tosc1)
Additional Delay
14CK + 4.1 ms
14CK + 4.1 ms
14CK + 65 ms
14CK + 65 ms
14CK + 4.1 ms
14CK + 65 ms
(V
from Reset
CC
14CK
14CK
18 pF
6 pF
= 5.0V)
(2)
(1)
(2)
(1)
(2)
Figure 9-2 on page
Cap (Xtal2/Tosc2)
CKSEL0
0
0
0
0
1
1
1
1
8 pF
6 pF
Table 9-7
SUT1:0
00
01
10
11
00
01
10
11
43.
45
at

Related parts for ATMEGA2560R231-AU