ATMEGA64A-MNR Atmel, ATMEGA64A-MNR Datasheet - Page 70

• Manufacturer Part Number: ATMEGA64A-MNR
• Description: IC MCU AVR 64K FLASH 8QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA64A-MNR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SPI, UART, I2C
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 53
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Operating Temperature Range: - 40 C to + 85 C
• Processor To Be Evaluated: ATMEGA64A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13.2.2
8160C–AVR–07/09
Reading the Pin Value
If PORTxn is written logic one when the pin is configured as an output pin, the port pin is driven
high (one). If PORTxn is written logic zero when the pin is configured as an output pin, the port
pin is driven low (zero).
When switching between tri-state ({DDxn, PORTxn} = 0b00) and output high ({DDxn,
PORTxn } = 0b11), an intermediate state with either pull-up enabled ({DDxn, PORTxn} = 0b01)
or output low ({DDxn, PORTxn} = 0b10) must occur. Normally, the pull-up enabled state is fully
acceptable, as a high-impedant environment will not notice the difference between a strong high
driver and a pull-up. If this is not the case, the PUD bit in the SFIOR Register can be written to
one to disable all pull-ups in all ports.
Switching between input with pull-up and output low generates the same problem. The user
must use either the tri-state ({DDxn, PORTxn} = 0b00) or the output high state({DDxn,
PORTxn} = 0b11) as an intermediate step.
Table 13-1
Table 13-1.
Independent of the setting of Data Direction bit DDxn, the port pin can be read through the
PINxn Register bit. As shown in
stitute a synchronizer. This is needed to avoid metastability if the physical pin changes value
near the edge of the internal clock, but it also introduces a delay.
gram of the synchronization when reading an externally applied pin value. The maximum and
minimum propagation delays are denoted t
DDxn
0
0
0
1
1
PORTxn
summarizes the control signals for the pin value.
0
1
1
0
1
Port Pin Configurations
(in SFIOR)
PUD
X
X
X
0
1
Figure
Output
Output
Input
Input
Input
I/O
13-2, the PINxn Register bit and the preceding latch con-
pd,max
Pull-up
Yes
No
No
No
No
and t
pd,min
Comment
Tri-state (Hi-Z)
Pxn will source current if ext. pulled low.
Tri-state (Hi-Z)
Output Low (Sink)
Output High (Source)
respectively.
Figure 13-3
ATmega64A
shows a timing dia-
70