MCF53014CMJ240J Freescale Semiconductor, MCF53014CMJ240J Datasheet - Page 19

• Manufacturer Part Number: MCF53014CMJ240J
• Description: IC MCU 32BIT 128KB 256MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF5301xr

Specifications of MCF53014CMJ240J

• Core Processor: Coldfire V3
• Core Size: 32-Bit
• Speed: 240MHz
• Connectivity: EBI/EMI, Ethernet, I²C, MMC, SPI, SSI, UART/USART, USB, USB OTG
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 83
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: Cache
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 1.08 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• Processor Series: MCF5301x
• Core: ColdFire V3
• Data Bus Width: 32 bit
• Data Ram Size: 16 bit
• Interface Type: I2C, UART, DSPI
• Maximum Clock Frequency: 400 KHz, 20 MHz, 25 MHz
• Number Of Timers: 4
• Operating Supply Voltage: - 0.5 V to + 2 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: M53015EVB, M53017KIT, M53017MOD
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13 bit
• On-chip Dac: 16 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

5
This document contains electrical specification tables and reference timing diagrams for the MCF5301x microprocessor. This
section contains detailed information on DC/AC electrical characteristics and AC timing specifications.
The electrical specifications are preliminary and are from previous designs or design simulations. These specifications may not
be fully tested or guaranteed at this early stage of the product life cycle, however for production silicon these specifications will
be met. Finalized specifications will be published after complete characterization and device qualifications have been
completed.
5.1
Freescale Semiconductor
Preliminary Electrical Characteristics
Maximum Ratings
1
2
3
4
5
Core Supply Voltage
CMOS Pad Supply Voltage
DDR/Memory Pad Supply Voltage
PLL Supply Voltage
Digital Input Voltage
Instantaneous Maximum Current
Single pin limit (applies to all pins)
Operating Temperature Range (Packaged)
Storage Temperature Range
The parameters specified in this MCU document supersede any values found in the module
specifications.
Functional operating conditions are given in
Absolute maximum ratings are stress ratings only, and functional operation at the maxima is
not guaranteed. Continued operation at these levels may affect device reliability or cause
permanent damage to the device.
This device contains circuitry protecting against damage due to high static voltage or
electrical fields; however, it is advised that normal precautions be taken to avoid application of
any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of
operation is enhanced if unused inputs are tied to an appropriate logic voltage level (e.g.,
either V
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive and negative clamp voltages,
then use the larger of the two values.
All functional non-supply pins are internally clamped to V
Power supply must maintain regulation within operating EV
and operating maximum current conditions. If positive injection current (V
than I
going out of regulation. Insure external EV
injection current. This will be the greatest risk when the MCU is not consuming power (ex; no
clock). Power supply must maintain regulation within operating EV
instantaneous and operating maximum current conditions.
DD
SS
, the injection current may flow out of EV
or EV
DD
Rating
3
).
Preliminary—Subject to Change Without Notice
Table 7. Absolute Maximum Ratings
MCF5301x Data Sheet, Rev. 5
3, 4, 5
NOTE
DD
Section 5.4, “DC Electrical
load will shunt current greater than maximum
DD
(T
Symbol
PLLV
SDV
EV
L
IV
and could result in external power supply
T
V
T
I
– T
stg
D
DD
IN
A
DD
DD
DD
H
SS
)
DD
and EV
range during instantaneous
–0.5 to +2.0
–0.3 to +4.0
–0.3 to +4.0
–0.3 to +2.0
–55 to +150
–0.3 to +3.6
–40 to +85
1, 2
DD
Value
DD
Preliminary Electrical Characteristics
25
range during
.
Specifications.”
in
> EV
DD
) is greater
Unit
mA
°C
°C
V
V
V
V
V
19