AT32UC3L0-XPLD Atmel, AT32UC3L0-XPLD Datasheet - Page 103
AT32UC3L0-XPLD
Manufacturer Part Number
AT32UC3L0-XPLD
Description
KIT DEV/EVAL FOR AT32UC3L0
Manufacturer
Atmel
Datasheet
1.AT32UC3L016-D3HT.pdf
(110 pages)
Specifications of AT32UC3L0-XPLD
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3L0-XPLD
Manufacturer:
Atmel
Quantity:
135
- Current page: 103 of 110
- Download datasheet (2Mb)
10.4.22
10.4.23
32099F–11/2010
Chip
I/O Pins
6. The aWire debug interface is reset after leaving Shutdown mode
1. Power consumption in static mode is too high
2. Shutdown mode is not functional
3. VDDIN current consumption increase above 1.8V
4. Increased Power Consumption in VDDIO in sleep modes
1. PB10 is not 3.3V tolerant
2. Analog multiplexing consumes extra power
3. PA02, PB01, PB04, PB05, and RESET_N have half of the pull-up strength
4. OCD MCKO and MDO[3] are swapped in the AUX1 mapping
If the aWire debug mode is used as debug interface and the program enters Shutdown
mode, the aWire interface will be reset when the device receives a wakeup either from the
WAKE_N pin or the AST.
Fix/Workaround
None.
Power consumption in static mode is too high when PA21 is high.
Fix/Workaround
Ensure PA21 is low.
Do not enter Shutdown mode.
Fix/Workaround
None.
When VDDIN increases above 1.8V, current on VDDIN increases with up to 40µA.
Fix/Workaround
None.
If the OSC0 is enabled in crystal mode when entering a sleep mode where the OSC0 is dis-
abled, this will lead to an increased power consumption in VDDIO.
Fix/Workaround
Solution 1: Disable the OSC0 by writing a zero to the Oscillator Enable bit in the System
Control Interface (SCIF) Oscillator Control Register (SCIF.OSC0CTRL.OSCEN) before
going to any sleep mode where the OSC0 is disabled
Solution 2: Pull down or up XIN0 and XOUT0 with 1Mohm resistor.
PB10 should be grounded on the PCB and left unused.
Fix/Workaround
None.
Current consumption on VDDIO increases when the voltage on analog inputs is close to
VDDIO/2.
Fix/Workaround
None.
Pins PA02, PB01, PB04, PB05, and RESET_N have half of the specified pull-up strength.
Fix/Workaround
None.
When using the OCD AUX1 mapping of trace signals MDO[3] is located on pin PB05
and MCKO is located on PB01.
AT32UC3L016/32/64
103
Related parts for AT32UC3L0-XPLD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVAL AVR32 UC3 MCU
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: