AT32UC3L0-XPLD Atmel, AT32UC3L0-XPLD Datasheet - Page 89
AT32UC3L0-XPLD
Manufacturer Part Number
AT32UC3L0-XPLD
Description
KIT DEV/EVAL FOR AT32UC3L0
Manufacturer
Atmel
Datasheet
1.AT32UC3L016-D3HT.pdf
(110 pages)
Specifications of AT32UC3L0-XPLD
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3L0-XPLD
Manufacturer:
Atmel
Quantity:
135
- Current page: 89 of 110
- Download datasheet (2Mb)
10.2.14
10.2.15
10.3
10.4
10.4.1
32099F–11/2010
Rev. C
Rev. B
Chip
I/O Pins
Processor and Architecture
1. Increased Power Consumption in VDDIO in sleep modes
2. In 3.3V Single Supply Mode the Analog Comparator inputs affects the device’s ability
1. PA17 has low ESD tolerance
Not sampled.
1. Privilege violation when using interrupts in application mode with protected system
2. Hardware breakpoints may corrupt MAC results
None
If the OSC0 is enabled in crystal mode when entering a sleep mode where the OSC0 is dis-
abled, this will lead to an increased power consumption in VDDIO.
Fix/Workaround
Solution 1: Disable the OSC0 by writing a zero to the Oscillator Enable bit in the System
Control Interface (SCIF) Oscillator Control Register (SCIF.OSC0CTRL.OSCEN) before
going to any sleep mode where the OSC0 is disabled
Solution 2: Pull down or up XIN0 and XOUT0 with 1MOhm resistor.
to start
When using the 3.3V Single Supply Mode the state of the Analog Comparator input pins can
affect the device’s ability to release POR reset.
This is due to an interaction between the Analog Comparator input pins and the POR cir-
cuitry. The issue is not present in the 1.8V Single Supply Mode or the 3.3V Supply mode
with 1.8V Regulated I/O Lines.
Fix/Workaround
ACREFN (pin PA16) must be connected to GND until the POR reset is released and the
Analog Comparator inputs should not be driven higher than 1.0 V until the POR reset is
released.
PA17 only tolerates 500V ESD pulses (Human Body Model).
Fix/Workaround
Care must be taken during manufacturing and PCB design.
stack
If the system stack is protected by the MPU and an interrupt occurs in application mode, an
MPU DTLB exception will occur.
Fix/Workaround
Make a DTLB Protection (Write) exception handler which permits the interrupt request to be
handled in privileged mode.
Hardware breakpoints on MAC instructions may corrupt the destination register of the MAC
instruction.
Fix/Workaround
Place breakpoints on earlier or later instructions.
AT32UC3L016/32/64
89
Related parts for AT32UC3L0-XPLD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
KIT EVAL AVR32 UC3 MCU
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: