PIC16LF819T-I/SSTSL Microchip Technology, PIC16LF819T-I/SSTSL Datasheet - Page 173

• Manufacturer Part Number: PIC16LF819T-I/SSTSL
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SSOP,20PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16LF819T-I/SSTSL

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: PIC16LF819TISSTSL

15.3.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA<5>), or the Continuous Receive
Enable bit, CREN (RCSTA<4>). Data is sampled on the
RX pin on the falling edge of the clock.
If enable bit, SREN, is set, only a single word is
received. If enable bit, CREN, is set, the reception is
continuous until CREN is cleared. If both bits are set,
then CREN takes precedence.
To set up a Synchronous Master Reception:
1.
2.
FIGURE 15-13:
TABLE 15-8:
© 2008 Microchip Technology Inc.
INTCON
PIR1
PIE1
IPR1
RCSTA
RCREG
TXSTA
BAUDCON ABDOVF
SPBRGH
SPBRG
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
Note: Timing diagram demonstrates Sync Master mode with SREN bit = 1 and BRGH bit = 0.
Name
RC6/TX/CK pin
RC6/TX/CK pin
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRG16
bit, as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
RC7/RX/DT
(SCKP = 0)
(SCKP = 1)
(Interrupt)
CREN bit
SREN bit
SREN bit
RCIF bit
RXREG
Write to
Read
EUSART SYNCHRONOUS MASTER
RECEPTION
EUSART Receive Register
EUSART Baud Rate Generator Register High Byte
EUSART Baud Rate Generator Register Low Byte
pin
GIE/GIEH
Q2
CSRC
SPEN
Bit 7
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘0’
—
—
—
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
PEIE/GIEL
RCIDL
ADIE
ADIP
ADIF
Bit 6
RX9
TX9
bit 0
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
TMR0IE
bit 1
SREN
TXEN
RCIF
RCIE
RCIP
Bit 5
—
bit 2
INT0IE
CREN
SYNC
SCKP
Bit 4
TXIF
TXIE
TXIP
bit 3
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE
ADDEN
SENDB
BRG16
RBIE
Bit 3
Ensure bits, CREN and SREN, are clear.
If interrupts are desired, set enable bit, RCIE.
If 9-bit reception is desired, set bit, RX9.
If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
Interrupt flag bit, RCIF, will be set when reception
is complete and an interrupt will be generated if
the enable bit, RCIE, was set.
Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
bit, CREN.
bits in the INTCON register (INTCON<7:6>) are
set.
—
—
—
bit 4
PIC18F2450/4450
TMR0IF
CCP1IE
CCP1IP
CCP1IF
BRGH
FERR
Bit 2
bit 5
—
TMR2IE TMR1IE
TMR2IP TMR1IP
bit 6
TMR2IF
INT0IF
OERR
TRMT
WUE
Bit 1
TMR1IF
ABDEN
bit 7
DS39760D-page 171
RX9D
TX9D
RBIF
Bit 0
Q1 Q2 Q3 Q4
on Page:
Values
Reset
49
51
51
51
51
50
51
51
51
50
‘0’