VS6624Q0KP STMicroelectronics, VS6624Q0KP Datasheet - Page 34
VS6624Q0KP
Manufacturer Part Number
VS6624Q0KP
Description
Display Modules & Development Tools CAMERA MODULE SINGLE CHIP 1.3MEGA
Manufacturer
STMicroelectronics
Datasheet
1.VS6624Q0KP.pdf
(106 pages)
Specifications of VS6624Q0KP
Description/function
Camera Module
Interface Type
Two-Wire Serial
Data Bus Width
8 bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 34 of 106
- Download datasheet (2Mb)
Getting started
9
Initial power up
Minimum startup command sequence
34/106
Getting started
Before any communication is possible with the VL6624/VS6624 the following steps must
take place:
1.
2.
3.
4.
These steps can all take place simultaneously. After these steps are complete a delay of
200 µs is required before any I²C communication can take place, see
sequence
1.
2.
3.
The above three commands represent the absolute minimum required to get video data
output.
The default configuration results in an output of SXGA, 15 fps, YUV data format with ITU
embedded codes requiring a external clock frequency of 12MHz.
In practice the user is likely to require to write some additional setup information prior to
receive the required data output.
Apply VDD (1.8V or 2.8V)
Apply AVDD (2.8V)
Apply an external CLOCK (6.5MHz to 54MHz)
Assert CE line HIGH
Enable the microprocessor - before any commands can be sent to the
VL6624/VS6624, the internal microprocessor must be enabled by writing the value
0x02 to the MicroEnable register 0xC003 found in the
Section.
Enable the digital I/O - after power up the digital I/O of the VL6624/VS6624 is in a high-
impedance state (‘tri-state’). The I/O are enabled by writing the value 0x01 to the
DIO_Enable register 0xC044 found in the
The user can then program the system clock frequency and setup the required output
format before placing the VL6624/VS6624 in RUN mode by writing 0x02 to the
interface manager control
.
register 0x0180.
Low level control registers
Low level control registers
Figure 3: Power up
Section.
VL6624/VS6624
Host
Related parts for VS6624Q0KP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: