ADUC7061BCPZ32-RL Analog Devices Inc, ADUC7061BCPZ32-RL Datasheet - Page 88

• Manufacturer Part Number: ADUC7061BCPZ32-RL
• Description: DUAL 24-BIT AFE AND ARM 7 I.C
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7061BCPZ32-RL

• Design Resources: USB Based Temperature Monitor Using ADuC7061 and an External RTD (CN0075) 4 mA-to-20 mA Loop-Powered Temperature Monitor Using ADuC7060/1 (CN0145)
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 10MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 8
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 2.625 V
• Data Converters: A/D 5x24b, 8x24b, D/A 1x14b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuC7060/ADuC7061
I
Name:
Address:
Default value:
Access:
Function:
Table 97. I2CMSTA MMR Bit Designations
Bit
15:11
10
9
8
7
6
5
4
3
2
1:0
2
C Master Status, I2CMSTA, Register
Name
I2CBBUSY
I2CMRxFO
I2CMTC
I2CMNA
I2CMBUSY
I2CAL
I2CMNA
I2CMRXQ
I2CMTXQ
I2CMTFSTA
I2CMSTA
0xFFFF0904
0x0000
Read only
This 16-bit MMR is the I
Description
Reserved. These bits are reserved.
I
This bit is set to 1 when a start condition is detected on the I
This bit is cleared when a stop condition is detected on the bus.
Master receive FIFO overflow.
This bit is set to 1 when a byte is written to the receive FIFO when it is already full.
This bit is cleared in all other conditions.
I
This bit is set to 1 when a transmission is complete between the master and the slave with which it was
communicating. If the I2CMCENI bit in I2CMCON is set, an interrupt is generated when this bit is set.
Clear this interrupt source.
I
This bit is set to 1 when a no acknowledge condition is received by the master in response to a data write transfer. If
the I2CNACKENI bit in I2CMCON is set, an interrupt is generated when this bit is set.
This bit is cleared in all other conditions.
I
Set to 1 when the master is busy processing a transaction.
Cleared if the master is ready or if another master device has control of the bus.
I
This bit is set to 1 when the I
interrupt is generated when this bit is set.
This bit is cleared in all other conditions.
I
This bit is set to 1 when a no acknowledge condition is received by the master in response to an address. If the
I2CNACKENI bit in I2CMCON is set, an interrupt is generated when this bit is set.
This bit is cleared in all other conditions.
I
This bit is set to 1 when data enters the receive FIFO. If the I2CMRENI in I2CMCON is set, an interrupt is generated.
This bit is cleared in all other conditions.
I
This bit goes high if the transmit FIFO is empty or contains only one byte and the master has transmitted an address
+ write. If the I2CMTENI bit in I2CMCON is set, an interrupt is generated when this bit is set.
This bit is cleared in all other conditions.
I
[00] = I
[01] = 1 byte in master transmit FIFO.
[10] = 1 byte in master transmit FIFO.
[11] = I
2
2
2
2
2
2
2
2
2
C bus busy status bit.
C transmission complete status bit.
C master no acknowledge data bit
C master busy status bit.
C arbitration lost status bit.
C master no acknowledge address bit.
C master receive request bit.
C master transmit request bit.
C master transmit FIFO status bits.
2
2
C master transmit FIFO empty.
C master transmit FIFO full.
2
C status register in master mode.
2
C master does not gain control of the I
Rev. B | Page 88 of 108
2
C bus.
2
C bus. If the I2CALENI bit in I2CMCON is set, an