CY8C3665AXI-010 Cypress Semiconductor Corp, CY8C3665AXI-010 Datasheet - Page 28

• Manufacturer Part Number: CY8C3665AXI-010
• Description: PSOC3
• Manufacturer: Cypress Semiconductor Corp
• Series: PSOC™ 3 CY8C36xxr

Specifications of CY8C3665AXI-010

• Package / Case: *
• Voltage - Supply (vcc/vdd): 1.71 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 67MHz
• Number Of I /o: 62
• Eeprom Size: 1K x 8
• Core Processor: 8051
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Program Memory Size: 32KB (32K x 8)
• Data Converters: A/D 2x12b, D/A 4x8b
• Oscillator Type: Internal
• Peripherals: CapSense, DMA, POR, PWM, WDT
• Connectivity: EBI/EMI, I²C, LIN, SPI, UART/USART
• Core Size: 8-Bit
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Technology: CMOS
• Processing Unit: Microcontroller
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Supply Voltage (max): 5.5V
• Package Type: TQFP
• Screening Level: Industrial
• Pin Count: 100
• Mounting: Surface Mount
• Rad Hardened: No
• Processor Series: CY8C36
• Core: 8051
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SPI, UART, USB
• Maximum Clock Frequency: 67 MHz
• Number Of Programmable I/os: 28 to 72
• Number Of Timers: 4
• Operating Supply Voltage: 0.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Controller Family/series: (8051) PSOC 3
• No. Of I/o's: 62
• Eeprom Memory Size: 1KB
• Ram Memory Size: 4KB
• Cpu Speed: 67MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 6-2. Analog/Digital Low Voltage Interrupt, Analog High
Voltage Interrupt
6.3.1.2 Other Reset Sources
Note
Document Number: 001-53413 Rev. *J
17. GPIOs with opamp outputs are not recommended for use with CapSense
Interrupt
ALVI, DLVI, AHVI – Analog/Digital Low Voltage Interrupt,
Analog High Voltage Interrupt
Interrupt circuits are available to detect when Vdda and Vddd
go outside a voltage range. For AHVI, Vdda is compared to a
fixed trip level. For ALVI and DLVI, Vdda and Vddd are
compared to trip levels that are programmable, as listed in
Table
a device reset instead of an interrupt.
The monitors are disabled until after IPOR. During sleep mode
these circuits are periodically activated (buzzed). If an interrupt
occurs during buzzing then the system first enters its wake up
sequence. The interrupt is then recognized and may be
serviced.
XRES – External Reset
PSoC 3 has either a single GPIO pin that is configured as an
external reset or a dedicated XRES pin. Either the dedicated
XRES pin or the GPIO pin, if configured, holds the part in reset
while held active (low). The response to an XRES is the same
as to an IPOR reset.
The external reset is active low. It includes an internal pull-up
resistor. XRES is active during sleep and hibernate modes.
SRES – Software Reset
A reset can be commanded under program control by setting
a bit in the software reset register. This is done either directly
by the program or indirectly by DMA access. The response to
a SRES is the same as after an IPOR reset.
Another register bit exists to disable this function.
DRES – Digital Logic Reset
A logic signal can be routed from the UDBs or other digital
peripheral source through the DSI to the Configurable XRES
pin, P1[2], to generate a hardware-controlled reset. The pin
must be placed in XRES mode. The response to a DRES is the
same as after an IPOR reset.
WRES – Watchdog Timer Reset
The watchdog reset detects when the software program is no
longer being executed correctly. To indicate to the watchdog
timer that it is running correctly, the program must periodically
reset the timer. If the timer is not reset before a user-specified
amount of time, then a reset is generated.
Note IPOR disables the watchdog function. The program must
enable the watchdog function at an appropriate point in the
code by setting a register bit. When this bit is set, it cannot be
cleared again except by an IPOR power on reset event.
AHVI
DLVI
ALVI
6-2. ALVI and DLVI can also be configured to generate
Supply
Vddd
Vdda
Vdda
1.71 V–5.5 V 1.70 V–5.45 V in
1.71 V–5.5 V 1.70 V–5.45 V in
1.71 V–5.5 V 5.75 V
Voltage
Normal
Range
250 mV
increments
250 mV
increments
Available Trip
Settings
PRELIMINARY
Accuracy
±2%
±2%
±2%
6.4 I/O System and Routing
PSoC I/Os are extremely flexible. Every GPIO has analog and
digital I/O capability. All I/Os have a large number of drive modes,
which are set at POR. PSoC also provides up to four individual
I/O voltage domains through the Vddio pins.
There are two types of I/O pins on every device; those with USB
provide a third type. Both General Purpose I/O (GPIO) and
Special I/O (SIO) provide similar digital functionality. The primary
differences are their analog capability and drive strength.
Devices that include USB also provide two USBIO pins that
support specific USB functionality as well as limited GPIO
capability.
All I/O pins are available for use as digital inputs and outputs for
both the CPU and digital peripherals. In addition, all I/O pins can
generate an interrupt. The flexible and advanced capabilities of
the PSoC I/O, combined with any signal to any pin routability,
greatly simplify circuit design and board layout. All GPIO pins can
be used for analog input, CapSense
while SIO pins are used for voltages in excess of V
programmable output voltages.
Features supported by both GPIO and SIO:
Additional features only provided on the GPIO pins:
Additional features only provided on SIO pins:
USBIO features:
PSoC
User programmable port reset state
Separate I/O supplies and voltages for up to four groups of I/O
Digital peripherals use DSI to connect the pins
Input or output or both for CPU and DMA
Eight drive modes
Every pin can be an interrupt source configured as rising
edge, falling edge or both edges. If required, level sensitive
interrupts are supported through the DSI
Dedicated port interrupt vector for each port
Slew rate controlled digital output drive mode
Access port control and configuration registers on either port
basis or pin basis
Separate port read (PS) and write (DR) data registers to avoid
read modify write errors
Special functionality on a pin by pin basis
LCD segment drive on LCD equipped devices
CapSense
Analog input and output capability
Continuous 100 µA clamp current capability
Standard drive strength down to 1.7 V
Higher drive strength than GPIO
Hot swap capability (5 V tolerance at any operating V
Programmable and regulated high input and output drive
levels down to 1.2 V
No analog input, CapSense, or LCD capability
Over voltage tolerance up to 5.5 V
SIO can act as a general purpose analog comparator
Full speed USB 2.0 compliant I/O
Highest drive strength for general purpose use
Input, output, or both for CPU and DMA
Input, output, or both for digital peripherals
Digital output (CMOS) drive mode
Each pin can be an interrupt source configured as rising
edge, falling edge, or both edges
®
[17]
3: CY8C36 Family Datasheet
[17]
, and LCD segment drive,
DDA
Page 28 of 111
and for
DD
)
[+] Feedback
[+] Feedback