CYII4SC014KAA-GTC Cypress Semiconductor Corp, CYII4SC014KAA-GTC Datasheet - Page 13

• Manufacturer Part Number: CYII4SC014KAA-GTC
• Description: IC SENSOR IMAGE COLOR 49-PGA
• Manufacturer: Cypress Semiconductor Corp
• Type: CMOS Imagingr

Specifications of CYII4SC014KAA-GTC

• Package / Case: 49-PGA
• Pixel Size: 8µm x 8µm
• Active Pixel Array: 3048H x 4560V
• Frames Per Second: 3
• Voltage - Supply: 3.3V
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 50 C
• Minimum Operating Temperature: 0 C
• Image Size: 4560 H x 3048 V
• Color Sensing: Color
• Package: 49PGA
• Operating Temperature: 0 to 50 °C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
• Other names: IBIS4-14000-C; IBIS4-14000-C

Table 7. Serial Sensor Parameters Register Bit Definitions
Three pins are used for the serial data interface. This interface converts the serial data into an (internal) parallel data bus
(Serial-Parallel Interface or SPI). The control lines are:
■
■
■
The initial state of the register is undefined. However, no state exists that destroys the device.
Document #: 38-05709 Rev. *D
0 (LSB)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15 (MSB)
BIT
DATA: The data input. LSB is clocked in first.
CLK: Clock, on each rising edge, the value of DATA is clocked in
CS: Chip select, a rising edge on CS loads the parallelized data into the on-chip register.
set to zero (0).
1 = power on sensor array ; 0 = power-down.
1 = power up output amplifier 4; 0 = power-down.
1 = power up output amplifier 3; 0 = power-down.
1 = power up output amplifier 2; 0 = power-down.
1 = power up output amplifier 1; 0 = power-down.
3-bit code for subsampling mode of X shift register:
000 = full resolution
001 = full resolution
010 = full resolution
3-bit code for subsampling mode of Y shift registers:
000 = select 2, skip 2
001 = full resolution
010 = select 2, skip 2
Crossbar switch (output multiplexer) control bit initial value.
This initial value is clocked into the crossbar switch at a SYNC_YR rising edge pulse (when the array pointers
jump back to row 1).
The crossbar switch control bit selects the correspondence between multiplexer busses and output amplifiers.
Bus-to-output correspondence is according to the following table:
Bus
1 = Toggle crossbar switch control bit on every odd/even line. In order to let green pixels always use the same
output amplifier automatically, this bit must be set to 1. On every CLK_Y rising edge (when a new row is selected),
the crossbar switch control bit will toggle. Initial value (after SYNC_Y) is set by bit 12.
Not used.
1 = Power-up sensor array; 0 = Power-down.
1
2
3 (4 outputs)
4 (4 outputs)
Description’
when bit set to 0
output 1
output 2
output 3
output 4
011 = select 4, skip 20
100 = select 4, skip 4
101 = select 4, skip 8
011 = select 2, skip 4
100 = select 2, skip 2
101 = select 2, skip 2
when bit set to 1
output 4
output 3
output 2
output 1
CYII4SM014KAA-GEC
CYII4SC014KAA-GTC
Page 13 of 27
[+] Feedback