LAN9311-NZW Standard Microsystem (Smsc), LAN9311-NZW Datasheet - Page 139
![no-image](/images/no-image-200.jpg)
LAN9311-NZW
Manufacturer Part Number
LAN9311-NZW
Description
Ethernet Switch 2-Port 10Mbps/100Mbps 128-Pin XVTQFP
Manufacturer
Standard Microsystem (Smsc)
Datasheet
1.LAN9311-NU.pdf
(460 pages)
Specifications of LAN9311-NZW
Package
128XVTQFP
Phy/transceiver Interface
MII
Number Of Primary Switch Ports
2
Maximum Data Rate
100 Mbps
Internal Memory Buffer Size
32 KB
Vlan Support
Yes
Power Supply Type
Analog
Minimum Single Supply Voltage
3 V
Maximum Single Supply Voltage
3.6 V
Maximum Supply Current
0.295 A
Maximum Power Dissipation
1070 mW
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LAN9311-NZW
Manufacturer:
Standard
Quantity:
2
Company:
Part Number:
LAN9311-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
- Current page: 139 of 460
- Download datasheet (5Mb)
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Datasheet
SMSC LAN9311/LAN9311i
10.2.1
EEPROM Controller Operation
I
(E2P_CMD)
In Microwire EEPROM mode, the following operations are supported:
Note: In I
Note: The EEPROM Loader uses the READ command only.
The supported commands of each mode are detailed in
Register (E2P_CMD)," on page
Microwire) are explained in
respectively.
When issuing a WRITE, or WRAL command, the desired data must first be written into the
Data Register
EPC_COMMAND field of the
value. If the operation is a WRITE, the EPC_ADDRESS field in the
(E2P_CMD)
bit of the
when the EPC_BUSY bit is cleared.
When issuing a READ command, the EPC_COMMAND and EPC_ADDRESS fields of the
Command Register (E2P_CMD)
address, respectively. The READ command is executed by setting the EPC_BUSY bit of the
Command Register
bit is cleared, at which time the data from the EEPROM may be read from the
(E2P_DATA).
Other EEPROM operations (EWDS, EWEN, ERASE, ERAL, RELOAD) are performed by writing the
appropriate command into the EPC_COMMAND field of the
(E2P_CMD). The command is executed by setting the EPC_BUSY bit of the
Register
modifying the
Note: The EEPROM device powers-up in the erase/write disabled state. To modify the contents of
If an operation is attempted and the EEPROM device does not respond within 30mS, the
LAN9311/LAN9311i will time-out, and the EPC_TIMEOUT bit of the
(E2P_CMD)
2
C and Microwire master EEPROM operations are performed using the
ERASE (Erase Location)
ERAL (Erase All)
EWDS (Erase/Write Disable)
EWEN (Erase/Write Enable)
READ (Read Location)
WRITE (Write Location)
WRAL (Write All)
RELOAD (EEPROM Loader Reload - See
are supported.
the EEPROM, the EWEN command must first be issued.
EEPROM Command Register (E2P_CMD)
(E2P_CMD). In all cases, the software must wait for the EPC_BUSY bit to clear before
2
C EEPROM mode, only a sub-set of the above commands (READ, WRITE, and RELOAD)
must also be set to the desired location. The command is executed when the EPC_BUSY
and
will be set.
EEPROM Command Register
(E2P_DATA). The WRITE or WRAL command may then be issued by setting the
EEPROM Data Register
(E2P_CMD). The completion of the operation is indicated when the EPC_BUSY
Section 10.2.2, "I2C EEPROM"
EEPROM Command Register (E2P_CMD)
must be configured with the desired command value and the read
198. Details specific to each EEPROM controller mode (I
DATASHEET
139
(E2P_DATA).
(E2P_CMD).
Section 10.2.4, "EEPROM
is set. The completion of the operation is indicated
and
Section 14.2.4.1, "EEPROM Command
Section 10.2.3, "Microwire EEPROM"
EEPROM Command Register
EEPROM Command Register
EEPROM Command Register
EEPROM Command Register
Loader")
to the desired command
EEPROM Data Register
EEPROM Command
Revision 1.7 (06-29-10)
EEPROM
EEPROM
EEPROM
2
C and
Related parts for LAN9311-NZW
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN9303-ABZJ](/images/no-image3.png)
Part Number:
Description:
Ethernet Switch 3-Port 10Mbps/100Mbps 56-Pin QFN EP
Manufacturer:
Standard Microsystem (Smsc)
Datasheet:
![LAN9311I-NZW](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Standard Microsystem (Smsc)
Datasheet: