LAN9311-NZW Standard Microsystem (Smsc), LAN9311-NZW Datasheet - Page 155
![no-image](/images/no-image-200.jpg)
LAN9311-NZW
Manufacturer Part Number
LAN9311-NZW
Description
Ethernet Switch 2-Port 10Mbps/100Mbps 128-Pin XVTQFP
Manufacturer
Standard Microsystem (Smsc)
Datasheet
1.LAN9311-NU.pdf
(460 pages)
Specifications of LAN9311-NZW
Package
128XVTQFP
Phy/transceiver Interface
MII
Number Of Primary Switch Ports
2
Maximum Data Rate
100 Mbps
Internal Memory Buffer Size
32 KB
Vlan Support
Yes
Power Supply Type
Analog
Minimum Single Supply Voltage
3 V
Maximum Single Supply Voltage
3.6 V
Maximum Supply Current
0.295 A
Maximum Power Dissipation
1070 mW
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LAN9311-NZW
Manufacturer:
Standard
Quantity:
2
Company:
Part Number:
LAN9311-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
- Current page: 155 of 460
- Download datasheet (5Mb)
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Datasheet
Chapter 11 IEEE 1588 Hardware Time Stamp Unit
SMSC LAN9311/LAN9311i
11.1
11.1.1
The LAN9311/LAN9311i provides hardware support for the IEEE 1588 Precision Time Protocol (PTP),
allowing clock synchronization with remote Ethernet devices, packet time stamping, and time driven
event generation. Time stamping is supported on all ports, with an individual IEEE 1588 Time Stamp
module connected to each port via the MII bus. Any port may function as a master or a slave clock
per the IEEE 1588 specification, and the LAN9311/LAN9311i as a whole may function as a boundary
clock.
A 64-bit tunable clock is provided that is used as the time source for all IEEE 1588 time stamp related
functions. An IEEE 1588 Clock/Events block provides IEEE 1588 clock comparison based interrupt
generation and time stamp related GPIO event generation. Two LAN9311/LAN9311i GPIO pins
(GPIO[8:9]) can be used to trigger a time stamp capture when configured as an input, or output a
signal from the GPIO based on an IEEE 1588 clock target compare event when configured as an
output.
interface to other LAN9311/LAN9311i functions.
All features of the IEEE 1588 hardware time stamp unit can be monitored and configured via their
respective configuration and status registers. A detailed description of all IEEE 1588 CSRs is included
in
IEEE 1588
IEEE 1588 specifies a Precision Time Protocol (PTP) used by master and slave clock devices to pass
time information in order to achieve clock synchronization. Five network message types are defined:
Only the first four message types (Sync, Delay_Req, Follow_Up, Delay_Resp) are used for clock
synchronization. Using these messages, the protocol software may calculate the offset and network
delay between time stamps, adjusting the slave clock frequency as needed. Refer to the IEEE 1588
protocol for message definitions and proper usage.
A PTP domain is segmented into PTP sub-domains, which are then segmented into PTP
communication paths. Within each PTP communication path there is a maximum of one master clock,
which is the source of time for each slave clock. The determination of which clock is the master and
which clock(s) is(are) the slave(s) is not fixed, but determined by the IEEE 1588 protocol. Similarly,
each PTP sub-domain may have only one master clock, referred to as the Grand Master Clock.
PTP communication paths are conceptually equivalent to Ethernet collision domains and may contain
devices which extend the network. However, unlike Ethernet collision domains, the PTP
communication path does not stop at a network switch, bridge, or router. This leads to a loss of
precision when the network switch/bridge/router introduces a variable delay. Boundary clocks are
defined which conceptually bypass the switch/bridge/router (either physically or via device integration).
Essentially, a boundary clock acts as a slave to an upstream master, and as a master to a down stream
slave. A boundary clock may contain multiple ports, but a maximum of one slave port is permitted.
For more information on the IEEE 1588 protocol, refer to the National Institute of Standards and
Technology IEEE 1588 website:
http://ieee1588.nist.gov/
Functional Overview
Section 14.2.5, "IEEE 1588," on page
Sync
Delay_Req
Follow_Up
Delay_Resp
Management
Section 11.1.2, "Block Diagram"
DATASHEET
describes the various IEEE 1588 related blocks and how they
202.
155
Revision 1.7 (06-29-10)
Related parts for LAN9311-NZW
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN9303-ABZJ](/images/no-image3.png)
Part Number:
Description:
Ethernet Switch 3-Port 10Mbps/100Mbps 56-Pin QFN EP
Manufacturer:
Standard Microsystem (Smsc)
Datasheet:
![LAN9311I-NZW](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Standard Microsystem (Smsc)
Datasheet: