LAN9311-NZW Standard Microsystem (Smsc), LAN9311-NZW Datasheet - Page 410
![no-image](/images/no-image-200.jpg)
LAN9311-NZW
Manufacturer Part Number
LAN9311-NZW
Description
Ethernet Switch 2-Port 10Mbps/100Mbps 128-Pin XVTQFP
Manufacturer
Standard Microsystem (Smsc)
Datasheet
1.LAN9311-NU.pdf
(460 pages)
Specifications of LAN9311-NZW
Package
128XVTQFP
Phy/transceiver Interface
MII
Number Of Primary Switch Ports
2
Maximum Data Rate
100 Mbps
Internal Memory Buffer Size
32 KB
Vlan Support
Yes
Power Supply Type
Analog
Minimum Single Supply Voltage
3 V
Maximum Single Supply Voltage
3.6 V
Maximum Supply Current
0.295 A
Maximum Power Dissipation
1070 mW
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LAN9311-NZW
Manufacturer:
Standard
Quantity:
2
Company:
Part Number:
LAN9311-NZW
Manufacturer:
Microchip Technology
Quantity:
10 000
- Current page: 410 of 460
- Download datasheet (5Mb)
Revision 1.7 (06-29-10)
14.5.3.40
31:15
14:11
BITS
RESERVED
Drop Reason B
When bit 8 is set, these bits indicate the reason a packet was dropped per
the table below:
VALUES
Switch Engine Interrupt Pending Register (SWE_IPR)
This register contains the Switch Engine interrupt status. The status is double buffered. All interrupts
in this register may be masked via the
Refer to
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
BIT
Register #:
Chapter 5, "System Interrupts," on page 49
Admit Only VLAN was set and the packet was untagged or priority tagged.
The destination address was not in the ALR table (unknown or broadcast),
Enable Membership Checking on ingress was set, Admit Non Member was
cleared and the source port was not a member of the incoming VLAN.
The destination address was found in the ALR table but the source port was
not in the forwarding state.
The destination address was found in the ALR table but the destination port
was not in the forwarding state.
The destination address was found in the ALR table but Enable Membership
Checking on ingress was set and the destination port was not a member of the
incoming VLAN.
The destination address was found in the ALR table but the Enable
Membership Checking on ingress was set, Admit Non Member was cleared and
the source port was not a member of the incoming VLAN.
Drop Unknown was set and the destination address was a unicast but not in
the ALR table.
Filter Multicast was set and the destination address was a multicast and not in
the ALR table.
The packet was a broadcast but exceeded the Broadcast Throttling limit.
The destination address was not in the ALR table (unknown or broadcast) and
the source port was not in the forwarding state.
The destination address was found in the ALR table but the source and
destination ports were the same.
The destination address was found in the ALR table and the Filter bit was set
for that address.
RESERVED
RESERVED
A packet was received with a VLAN ID of FFFh
RESERVED
1881h
DESCRIPTION
DESCRIPTION
DATASHEET
Switch Engine Interrupt Mask Register (SWE_IMR)
410
Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface
Size:
for more information.
32 bits
TYPE
SMSC LAN9311/LAN9311i
RO
RC
DEFAULT
Datasheet
0h
-
register.
Related parts for LAN9311-NZW
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN9303-ABZJ](/images/no-image3.png)
Part Number:
Description:
Ethernet Switch 3-Port 10Mbps/100Mbps 56-Pin QFN EP
Manufacturer:
Standard Microsystem (Smsc)
Datasheet:
![LAN9311I-NZW](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
Standard Microsystem (Smsc)
Datasheet: