DSPB56374AE Freescale Semiconductor, DSPB56374AE Datasheet - Page 11

• Manufacturer Part Number: DSPB56374AE
• Description: IC DSP 24BIT 150MHZ 52-LQFP
• Manufacturer: Freescale Semiconductor
• Series: Symphony™r
• Type: Audio Processorr

Specifications of DSPB56374AE

• Interface: Host Interface, I²C, SAI, SPI
• Clock Rate: 150MHz
• Non-volatile Memory: ROM (84 kB)
• On-chip Ram: 54kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.25V
• Operating Temperature: -40°C ~ 110°C
• Mounting Type: Surface Mount
• Package / Case: 52-LQFP
• Product: DSPs
• Data Bus Width: 24 bit
• Processor Series: DSP563xx
• Core: 56000
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 150 MIPS
• Maximum Clock Frequency: 150 MHz
• Program Memory Type: Flash
• Program Memory Size: 24 KB
• Data Ram Size: 54 KB
• Operating Supply Voltage: 1.25 V or 3.3 V
• Maximum Operating Temperature: + 110 C
• Mounting Style: SMD/SMT
• Interface Type: SIA, SHI
• Minimum Operating Temperature: - 40 C
• Leaded Process Compatible: Yes
• Rohs Compliant: Yes
• Peak Reflow Compatible (260 C): Yes
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Freescale Semiconductor
Signal
HREQ
Name
MOSI
HA0
HA2
PH4
SS
Input, output, or
Input or Output
Input or output
disconnected
Signal Type
Input
Input
Input
State during
Ignored Input SPI Slave Select—This signal is an active low Schmitt-trigger input when
Table 9. Serial Host Interface Signals (continued)
Tri-stated
Tri-stated
Reset
DSP56374 Data Sheet, Rev. 4.2
SPI Master-Out-Slave-In—When the SPI is configured as a master, MOSI
is the master data output line. The MOSI signal is used in conjunction with
the MISO signal for transmitting and receiving serial data. MOSI is the slave
data input line when the SPI is configured as a slave. This signal is a
Schmitt-trigger input when configured for the SPI Slave mode.
I
configured for the I
signal is used to form the slave device address. HA0 is ignored when
configured for the I
This signal is tri-stated during hardware, software, and individual reset.
Thus, there is no need for an external pull-up in this state.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
configured for the SPI mode. When configured for the SPI Slave mode, this
signal is used to enable the SPI slave for transfer. When configured for the
SPI master mode, this signal should be kept de-asserted (pulled high). If it
is asserted while configured as SPI master, a bus error condition is flagged.
If SS is de-asserted, the SHI ignores SCK clocks and keeps the MISO
output signal in the high-impedance state.
I
configured for the I
HA2 signal is used to form the slave device address. HA2 is ignored in the
I
This pin has an internal pull up resistor.
This input is 5 V tolerant.
Host Request—This signal is an active low Schmitt-trigger input when
configured for the master mode but an active low output when configured for
the slave mode.
When configured for the slave mode, HREQ is asserted to indicate that the
SHI is ready for the next data word transfer and de-asserted at the first clock
pulse of the new data word transfer. When configured for the master mode,
HREQ is an input. When asserted by the external slave device, it will trigger
the start of the data word transfer by the master. After finishing the data word
transfer, the master will await the next assertion of HREQ to proceed to the
next transfer. This pin can also be programmed as GPIO.
Port H4—When HREQ is configured as GPIO, this signal is individually
programmable as input, output, or internally disconnected.
This pin has an internal pull up resistor.
This input is 5 V tolerant.
2
2
2
C Slave Address 0—This signal uses a Schmitt-trigger input when
C Slave Address 2—This signal uses a Schmitt-trigger input when
C master mode.
2
2
2
C mode. When configured for I
C master mode.
C mode. When configured for the I
Signal Description
2
C slave mode, the HA0
2
C Slave mode, the
Signal Groupings
11