CY7C64714-56PVXC Cypress Semiconductor Corp, CY7C64714-56PVXC Datasheet - Page 3

• Manufacturer Part Number: CY7C64714-56PVXC
• Description: IC MCU USB EZ FX1 16KB 56-SSOP
• Manufacturer: Cypress Semiconductor Corp
• Series: EZ-USB FX1™r

Specifications of CY7C64714-56PVXC

• Applications: USB Microcontroller
• Core Processor: 8051
• Program Memory Type: ROMless
• Controller Series: CY7C647xx
• Ram Size: 16K x 8
• Interface: I²C, USB, USART
• Number Of I /o: 24
• Voltage - Supply: 3.15 V ~ 3.45 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 56-SSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 4-1. Special Function Registers
4.3
FX1 supports the I
SCL and SDA pins have open-drain outputs and hysteresis
inputs. These signals must be pulled up to 3.3V, even if no I
device is connected.
4.4
All packages: 8- or 16-bit “FIFO” bidirectional data bus, multi-
plexed on I/O ports B and D. 128-pin package: adds 16-bit
output-only 8051 address bus, 8-bit bidirectional data bus.
4.5
During the power-up sequence, internal logic checks the I
port for the connection of an EEPROM whose first byte is
either 0xC0 or 0xC2. If found, it uses the VID/PID/DID values
in the EEPROM in place of the internally stored values (0xC0),
or it boot-loads the EEPROM contents into internal RAM
(0xC2). If no EEPROM is detected, FX1 enumerates using
internally stored descriptors. The default ID values for FX1 are
VID/PID/DID (0x04B4, 0x6473, 0xAxxx where xxx=Chip
revision).
Table 4-2. Default ID Values for FX1
Note:
Document #: 38-08039 Rev. *C
Vendor ID 0x04B4 Cypress Semiconductor
Product ID 0x6473 EZ-USB FX1
Device
release
2.
A
B
C
D
E
x
0
1
2
3
4
5
6
7
8
9
F
The I
2
I
Buses
USB Boot Methods
C bus SCL and SDA pins must be pulled up, even if an EEPROM is not connected. Otherwise this detection method does not work properly.
[2]
2
C Bus
0xAnnn Depends chip revision (nnn = chip
CKCON
PCON
TMOD
TCON
DPH0
DPH1
DPL0
DPL1
DPS
TH0
TH1
IOA
TL0
TL1
SP
8x
2
C bus as a master only at 100/400 KHz.
Default VID/PID/DID
revision where first silicon = 001)
AUTOPTRH1
AUTOPTRH2
AUTOPTRL1
AUTOPTRL2
reserved
reserved
MPAGE
SCON0
SBUF0
EXIF
IOB
9x
AUTOPTRSETUP
EP24FIFOFLGS
EP68FIFOFLGS
EP2468STAT
INT2CLR
INT4CLR
IOC
Ax
IE
2
2
C
C
GPIFSGLDATLNOX
4.6
Because the FX1’s configuration is soft, one chip can take on
the identities of multiple distinct USB devices.
When first plugged into USB, the FX1 enumerates automati-
cally and downloads firmware and USB descriptor tables over
the USB cable. Next, the FX1 enumerates again, this time as
a device defined by the downloaded information. This
patented two-step process, called ReNumeration , happens
instantly when the device is plugged in, with no hint that the
initial download step has occurred.
Two control bits in the USBCS (USB Control and Status)
register control the ReNumeration process: DISCON and
RENUM. To simulate a USB disconnect, the firmware sets
DISCON to 1. To reconnect, the firmware clears DISCON to 0.
Before reconnecting, the firmware sets or clears the RENUM
bit to indicate whether the firmware or the Default USB Device
will handle device requests over endpoint zero: if RENUM = 0,
the Default USB Device will handle device requests; if RENUM
= 1, the firmware will.
4.7
The FX1 fully supports bus-powered designs by enumerating
with less than 100 mA as required by the USB specification.
4.8
4.8.1
FX1 implements an autovector feature for INT2 and INT4.
There are 27 INT2 (USB) vectors, and 14 INT4 (FIFO/GPIF)
vectors. See EZ-USB Technical Reference Manual (TRM) for
more details.
GPIFSGLDATLX
GPIFSGLDATH
EP01STAT
GPIFTRIG
OEA
OEB
OEC
OED
OEE
IOD
IOE
Bx
ReNumeration™
Bus-powered Applications
Interrupt System
INT2 Interrupt Request and Enable Registers
IP
RCAP2H
RCAP2L
SCON1
T2CON
SBUF1
TH2
TL2
Cx
EICON
CY7C64713/14
PSW
Dx
ACC
EIE
Ex
Page 3 of 50
EIP
Fx
B