ADV601LCJST Analog Devices Inc, ADV601LCJST Datasheet - Page 11

• Manufacturer Part Number: ADV601LCJST
• Description: IC CODEC VIDEO DSP/SRL 120LQFP
• Manufacturer: Analog Devices Inc
• Type: Video Codecr

Specifications of ADV601LCJST

• Rohs Status: RoHS non-compliant
• Data Interface: DSP, Serial
• Resolution (bits): 8 b
• Sigma Delta: No
• Voltage - Supply, Analog: 4.5 V ~ 5.5 V
• Voltage - Supply, Digital: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 120-LQFP

REV. 0
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
Mode Control Register
Indirect (Write Only) Register Index 0x00
This register holds configuration data for the ADV601LC’s video interface format and controls several other video interface features.
For more information on formats and modes, see the Video Interface section. Bits in this register have the following functions:
[3:0]
[4]
FIFO Error, FIFOERR. This condition indicates that the host has been unable to keep up with the ADV601LC’s compressed
data supply or demand requirements. If this condition occurs during encode, the data stream will not be corrupted until
MERR indicates that the DRAM is also overflowed. If this condition occurs during decode, the video output will be
corrupted. If the system overflows the FIFO (disregarding a FIFOSTP condition) with too many writes in decode mode,
FIFOERR is asserted. This read only status bit indicates the following:
0
1
FIFO Stop, FIFOSTP. This condition indicates that the FIFO is full in decode mode and empty in encode mode.
In decode mode only, FIFOSTP status actually behaves more conservatively than this. In decode mode, even when
FIFOSTP is indicated, there are still 32 empty Dwords available in the FIFO and 32 more Dword writes can safely
be performed. This status bit indicates the following:
0
1
Memory Error, MERR. This condition indicates that an error has occurred at the DRAM memory interface. This condition can
be caused by a defective DRAM, the inability of the Host to keep up with the ADV601LC compressed data stream, or bit errors
in the data stream. Note that the ADV601LC recovers from this condition without host intervention.
0
1
Reserved (always read/write zero)
Interrupt Enable on CCIRER, IE_CCIRER. This mask bit selects the following:
0
1
Interrupt Enable on STATR, IE_STATR. This mask bit selects the following:
0
1
Interrupt Enable on LCODE, IE_LCODE. This mask bit selects the following:
0
1
Interrupt Enable on FIFOSRQ, IE_FIFOSRQ. This mask bit selects the following:
0
1
Interrupt Enable on FIFOERR, IE_FIFOERR. This mask bit selects the following:
0
1
Interrupt Enable on FIFOSTP, IE_FIFOSTP. This mask bit selects the following:
0
1
Interrupt Enable on MERR, IE_MERR. This mask bit selects the following:
0
1
Reserved (always read/write zero)
Video Interface Format, VIF[3:0]. These bits select the interface format. Valid settings include the following (all
other values are reserved):
0x0 CCIR-656, reset value
0x2 MLTPX (Philips)
VCLK Output Divided by two, VCLK2. This bit controls the following:
0
1
No FIFO Error condition, reset value (FIFO_ERR pin LO)
FIFO overflow (encode) or underflow (decode) (FIFO_ERR pin HI)
No FIFO Stop condition, reset value (FIFO_STP pin LO)
FIFO empty (encode) or full (decode) (FIFO_STP pin HI)
No memory error condition, reset value
Memory error
Disable CCIR-656 data error interrupt, reset value
Enable interrupt on error in CCIR-656 data
Disable Statistics Ready interrupt, reset value
Enable interrupt on Statistics Ready
Disable Last Code Read interrupt, reset value
Enable interrupt on Last Code Read from FIFO
Disable FIFO Service Request interrupt, reset value
Enable interrupt on FIFO Service Request
Disable FIFO Stop interrupt, reset value
Enable interrupt on FIFO Stop
Disable FIFO Error interrupt, reset value
Enable interrupt on FIFO Error
Disable memory error interrupt, reset value
Enable interrupt on memory error
Do not divide VCLK output (VCLKO = VCLK), reset value
Divide VCLK output by two (VCLKO = VCLK/2)
–11–
ADV601LC