SC18IS601IBS,151 NXP Semiconductors, SC18IS601IBS,151 Datasheet - Page 7

IC SPI TO I2C BUS 24-HVQFN

SC18IS601IBS,151

Manufacturer Part Number
SC18IS601IBS,151
Description
IC SPI TO I2C BUS 24-HVQFN
Manufacturer
NXP Semiconductors
Datasheet

Specifications of SC18IS601IBS,151

Package / Case
24-VQFN Exposed Pad, 24-HVQFN, 24-SQFN, 24-DHVQFN
Controller Type
I²C Bus Controller
Interface
SPI
Voltage - Supply
2.4 V ~ 3.6 V
Current - Supply
11mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Maximum Operating Frequency
12 MHz
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
3.6 V
Supply Voltage (min)
2.4 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
568-3511 - DEMO BOARD SPI TO I2C
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
568-4710
935286979151
SC18IS601IBS-S
NXP Semiconductors
SC18IS600_601_5
Product data sheet
6.2.1.1 Quasi-bidirectional output configuration
Quasi-bidirectional outputs can be used both as an input and output without the need to
reconfigure the pin. This is possible because when the pin outputs a logic HIGH, it is
weakly driven, allowing an external device to pull the pin LOW. When the pin is driven
LOW, it is driven strongly and able to sink a large current. There are three pull-up
transistors in the quasi-bidirectional output that serve different purposes.
One of these pull-ups, called the ‘very weak’ pull-up, is turned on whenever the pin latch
for the pin contains a logic 1. This very weak pull-up sources a very small current that will
pull the pin HIGH if it is left floating.
A second pull-up, called the ‘weak’ pull-up, is turned on when the pin latch for the pin
contains a logic 1 and the pin itself is also at a logic 1 level. This pull-up provides the
primary source current for a quasi-bidirectional pin that is outputting a 1. If this pin is
pulled LOW by an external device, the weak pull-up turns off, and only the very weak
pull-up remains on. In order to pull the pin LOW under these conditions, the external
device has to sink enough current to overpower the weak pull-up and pull the pin below its
input threshold voltage.
The third pull-up is referred to as the ‘strong’ pull-up. This pull-up is used to speed up
LOW-to-HIGH transitions on a quasi-bidirectional pin when the pin latch changes from a
logic 0 to a logic 1. When this occurs, the strong pull-up turns on for two system clock
cycles quickly pulling the pin HIGH.
The quasi-bidirectional pin configuration is shown in
Although the SC18IS600/601 is a 3 V device, most of the pins are 5 V tolerant. If 5 V is
applied to a pin configured in quasi-bidirectional mode, there will be a current flowing from
the pin to V
configured in quasi-bidirectional mode is discouraged.
A quasi-bidirectional pin has a Schmitt-triggered input that also has a glitch suppression
circuit.
Fig 6.
pin latch data
Quasi-bidirectional output configuration
DD
causing extra power consumption. Therefore, applying 5 V to pins
Rev. 05 — 28 July 2008
2 SYSTEM
CYCLES
CLOCK
P
input data
V
SS
strong
Figure
P
SC18IS600/601
6.
very
weak
SPI to I
P
glitch rejection
weak
© NXP B.V. 2008. All rights reserved.
2
V
C-bus interface
DD
002aab882
GPIOn,
IOn pin
7 of 30

Related parts for SC18IS601IBS,151