ICS1893Y-10LFT IDT, Integrated Device Technology Inc, ICS1893Y-10LFT Datasheet - Page 40
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
ICS1893Y-10LFT
Manufacturer Part Number
ICS1893Y-10LFT
Description
PHYCEIVER LOW PWR 3.3V 64-TQFP
Manufacturer
IDT, Integrated Device Technology Inc
Series
PHYceiver™r
Type
PHY Transceiverr
Specifications of ICS1893Y-10LFT
Protocol
MII
Voltage - Supply
3.14 V ~ 3.47 V
Mounting Type
Surface Mount
Package / Case
64-TQFP, 64-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Drivers/receivers
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
1893Y-10LFT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ICS1893Y-10LFT
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
7.2.1 Auto-Negotiation General Process
ICS1893 Rev C 6/6/00
The Auto-Negotiation sublayer uses a physical signaling technique that is transparent at the packet level
and all higher protocol levels. This technique builds on the link pulse mechanism employed in 10Base-T
operations and is fully compliant with clause 28 of the ISO/IEC 8802-3 standard.
During the auto-negotiation process, both the ICS1893 and its remote link partner use Fast Link Pulses
(FLPs) to simultaneously ‘ advertise’ (that is, exchange) information on their respective technology
capabilities as follows:
1. For the auto-negotiation process to take place, both the ICS1893 and its remote link partner must first
2. The ICS1893 obtains the data for its FLP bursts from the Auto-Negotiation Advertisement Register
3. Both the ICS1893 and the remote link partner substitute Fast Link Pulse (FLP) bursts in place of the
4. Similarly, the ICS1893 places the Auto-Negotiation data received from its remote link partner's FLP
5. After the ICS1893 and its remote link partner exchange technology capability information, the ICS1893
6. To indicate that the auto-negotiation process is complete, the ICS1893 sets bits 1.5 and 17.4 high to
both support and be enabled for Auto-Negotiation.
(Register 4).
Normal Link Pulses (NLPs). In each FLP burst, the ICS1893 transmits information on its technology
capability through its Link Control Word, which includes link configuration and status data.
bursts into the Auto-Negotiation Link Partner Ability Register (Register 5).
Auto-Negotiation sublayer contrasts the data in Registers 4 and 5 and automatically selects for the
operating mode the highest-priority technology that both Register 4 and 5 have in common. (That is,
both the ICS1893 and its remote link partner use a predetermined priority list for selecting the operating
mode, thereby ensuring that both sides of the link make the same selection.) As follows from Annex
28B of the ISO/IEC 8802-3 standard, the pre-determined technology priorities are listed from 1 (highest
priority) to 5 (lowest priority):
(1) 100Base-TX full duplex
(2) 100Base-T4. (The ICS1893 does not support this technology.)
(3) 100Base-TX (half duplex)
(4) 10Base-T full duplex
(5) 10Base-T (half duplex)
Table 7-1
place.
Table 7-1.
logic one. After successful completion of the auto-negotiation process, the ICS1893 Auto-Negotiation
sublayer performs the following steps:
a. It sets to logic one the Status Register’ s Auto-Negotiation Complete bit (bit 1.5, which is also
b. It enables the negotiated link technology (such as the 100Base Transmit modules and 100Base
c. It disables the unused technologies to reduce the overall power consumption.
ICS1893 Data Sheet - Release
If Register 4 Has These
Technologies:
(3) 100Base-TX half duplex
(4) 100Base-T full duplex
available in the QuickPoll register as bit 17.4).
Receive modules).
shows an example of how the selection process of the highest-priority technology takes
Example of Selection Process of Highest-Priority Technology
Copyright © 2000, Integrated Circuit Systems, Inc.
All rights reserved.
If Register 5 Has These
Technologies:
(1) 100Base-TX full duplex
(3) 100Base-TX half duplex
40
Resulting Highest-Priority Common
Technology from Auto-Negotiation
Sublayer
(3) 100Base-TX half duplex
Chapter 7 Functional Blocks
June, 2000