FL7930CM Fairchild Semiconductor, FL7930CM Datasheet
FL7930CM
Specifications of FL7930CM
Related parts for FL7930CM
FL7930CM Summary of contents
Page 1
... Part Number Temperature Range FL7930BM FL7930BMX -40 to +125°C FL7930CM FL7930CMX © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 Description The FL7930 is an active Power Factor Correction (PFC) controller for low-to high-power lumens applications that operate in Critical Conduction Mode (CRM). It uses a ...
Page 2
... Application Diagrams Figure 1. Typical Boost PFC Application for FL7930B Figure 2. Typical Application of Single-Stage Flyback Converter for FL7930B Line Filter AC INPUT Figure 3. Typical Boost PFC Application for FL7930C © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 FL7930B 1 8 INV VCC 2 GATE 7 OVP 3 ...
Page 3
... Internal Block Diagram © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 Figure 4. Functional Block Diagram for FL7930B Figure 5. Functional Block Diagram for FL7930C 3 www.fairchildsemi.com ...
Page 4
... For proper operation, the stray inductance in the gate driving path 7 OUT must be minimized. 8 VCC This is the IC supply pin. IC current and MOSFET drive current are supplied using this pin. © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 Figure 6. Pin Configurations (Top View) Description 4 www.fairchildsemi.com ...
Page 5
... Thermal Impedance Symbol Thermal Resistance, Junction-to-Ambient JA Note: 3. Regarding the test environment and PCB type, please refer to JESD51-2 and JESD51-10. © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 Parameter > <-0. Human Body Model, JESD22-A114 ...
Page 6
... Maximum On-Time Programming 1 T ON,MAX1 t Maximum On-Time Programming 2 ON,MAX2 Current-Sense Section Current-Sense Input Threshold V CS Voltage Limit I Input Bias Current CS,BS t Current-Sense Delay to Output CS,D © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 Condition V Increasing CC V Decreasing CC I =20mA -0.2V CC ...
Page 7
... Enable Threshold Voltage EN HY Enable Hysteresis EN T Thermal Shutdown Temperature SD T Hysteresis Temperature of TSD HYS Note: 4. These parameters, although guaranteed by design, are not production tested. © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 Condition (4) I =3mA DET I = -3mA DET V =1V~5V ZCD (4) T =25° ...
Page 8
... Comparison of FL7930B and FL7930C Function FL7930B RDY Pin None OVP Pin Integrated Control Range Integrated Compensation © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 FL7930B FL7930C No External Circuit for Additional OVP None Integrated Reduced Power Loss and BOM Cost Due to Additional OVP Circuit ...
Page 9
... Typical Performance Characteristics Figure 7. Voltage Feedback Input Threshold Figure 9. Stop Threshold Voltage (V Figure 11. Operating Supply Current (I © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 ) Figure 8. Start Threshold Voltage (V REF1 ) vs. T Figure 10. Startup Supply Current (I STOP A ) vs. T Figure 12. Output Upper Clamp Voltage (V ...
Page 10
... Typical Performance Characteristics Figure 13. Zero Duty Cycle Output Voltage (V vs Figure 15. Maximum On-Time Program Figure 17. Input High Clamp Voltage (V © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 ) Figure 14. Maximum On-Time Program 1 (t EAZ ) Figure 16. Current Sense Input Threshold Voltage Limit ON,MAX2 ) vs ...
Page 11
... Typical Performance Characteristics Figure 19. Output Voltage High (V Figure 21. Restart Timer Delay (t Figure 23. Output Saturation Voltage (V © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 ) vs. T Figure 20. Output Voltage Low ( vs. T Figure 22. OVP Threshold at OVP Pin (V RST A ) vs. T Figure 24. OVP Threshold Voltage (V ...
Page 12
... IC. The IC operating current decreases to reduce power consumption if the IC is disabled. Figure 27 is the timing chart of the internal circuit near the INV pin when rated-PFC output voltage is assumed at 390V V supply voltage is 15V. CC © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0 PFC CC exceeds V , 20mA ...
Page 13
... The RDY pin output remains floating until V is higher than 2V. CC Figure 29. Two Cases of RDY Triggered HIGH © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 CC and builds up higher Figure 30. Two Cases of RDY Triggered LOW 5. Control Range Compensation: On time is controlled by the output voltage compensator ...
Page 14
... ZCD goes below 1.4V. At the falling edge of comparator output, internal logic turns on the MOSFET. Figure 33. Auxiliary Voltage Threshold © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 When no ZCD signal is available, the PFC controller cannot turn on the MOSFET, so the controller checks every switching off time and forces MOSFET turn on when the off time is longer than 150μ ...
Page 15
... C2 attenuates gain at higher frequency. Boost gain by R1 helps raise the response time and improves phase margin. © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 Figure 38. Compensators Gain Curve For the transconductance error amplifier side, gain changes based on differential input ...
Page 16
... PFC. © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 Figure 42. Input and Output Current Near Input Figure 43. Input and Output Current Near Input ...
Page 17
... MOSFET and diode. To protect against this, FL7930 internally checks if the input AC voltage exists. If input © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 does not exist, soft-start is reset and waits until AC input is live again. Soft-start manages the turn-on time for smooth operation when it detects AC input is applied, which applies less voltage and current stress on startup ...
Page 18
... PFC output and the INV pin — closer to the INV pin is better. Relative high voltage close to the INV pin can be helpful. © 2011 Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 ZCD path is recommended close to auxiliary winding from boost inductor and to the ZCD pin ...
Page 19
... Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’ ...
Page 20
... Fairchild Semiconductor Corporation FL7930 • Rev. 1.0.0 20 www.fairchildsemi.com ...