SP000221217 Infineon Technologies, SP000221217 Datasheet
SP000221217
Specifications of SP000221217
Related parts for SP000221217
SP000221217 Summary of contents
Page 1
... Block Diagram Voltage source V Logic Voltage sensor 3 IN Logic ESD Signal GND Infineon Technologies AG Product Summary Operating voltage On-state resistance Load current (ISO) Current limitation Operating temperature T Package PG-TO220-7-11 1 protection Standard (staggered) Gate Overvoltage Current protection limit protection Limit for Charge pump ...
Page 2
... setup without the DUT connected to the generator according to ISO 7637-1 and DIN 40839 Load dump Infineon Technologies AG Function Diagnostic feedback: open drain, invers to input level Logic ground Input, activates the power switch in case of logical high signal Positive power supply voltage, the tab is shorted to this pin ...
Page 3
... GND pulled up = see diagram page 9; not subject to production test, specified by design Turn-on time Turn-off time =-40...+150°C Slew rate 30% V OUT , =-40...+150°C Slew rate off 70 to 40% V OUT , =-40...+150°C Infineon Technologies AG Symbol chip - case R : thJC thJA Symbol T =25 °C: ...
Page 4
... At supply voltage increase Supply voltages higher than V resistor in the GND connection is recommended). See also V circuit diagram page Add > 0, add Infineon Technologies AG Symbol =-40...+150°C: bb(on =-40...+150°C: bb(under =-40...+25°C: V bb(u rst =+150° =-40...+25°C: V bb(ucp =25...150°C: ...
Page 5
... This range for the current sense ratio refers to all devices. The accuracy of the k a factor of two by matching the value the case of current limitation the sense current I High. See figure 2b, page 10. V 10) Valid if was exceeded before. bb(u rst) 11) not subject to production test, specified by design Infineon Technologies AG I (pin 4 to 6&7) =-40° =25° =+150°C: T ...
Page 6
... I j Status leakage current 12) not subject to production test, specified by design 13) External pull up resistor required for open load detection in off state. 14 ground resistor R is used, add the voltage drop across this resistor. GND Infineon Technologies AG Symbol 10% after IS static son(IS) static after soff(IS) ...
Page 7
... An external short of output used, an offset voltage at the GND and ST pins will occur and the V ) Low ohmic short may reduce the output current bb ) Power Transistor off, high impedance 18 ) with external resistor between pin 4 and pin 6&7 19 Infineon Technologies AG Output Status Current Sense level level ...
Page 8
... DC conditions is not recommended. Current sense output I IS ESD-ZD GND ESD-Zener diode: 6.1 V typ., max 14 mA nominal IS Inductive and overvoltage output clamp V Z GND V clamped typ. ON Infineon Technologies AG Overvoltage protection of logic part + ESD 6.1 V typ 150 GND Reverse battery protection ...
Page 9
... V high PROFET GND Normal load current can be handled by the PROFET itself. Infineon Technologies AG V disconnect with charged external bb inductive load high 6 OUT 7 OUT OUT IN IN(T+) If other external inductive loads L are connected to the PROFET, additional elements like D are necessary. ...
Page 10
... Load 1 Load son(IS) The sense signal is not valid during settling time after turn or change of load current. Figure 1b: V turn on proper turn on under all conditions Infineon Technologies AG Figure 2a: Switching a lamp doff(ST) V OUT t off I t slc(IS soff(IS) Figure 2b: Switching a lamp with current limit: ...
Page 11
... I IS Figure 3a: Short circuit: shut down by overtempertature, reset by cooling IN I L(SCp L(SCr Heating up may require several milliseconds, depending on external conditions typ. increases with decreasing temperature. L(SCp) Infineon Technologies AG Figure 4a: Overtemperature: Reset if T < Figure 5a: Open load: detection in ON-state, open load occurs in on-state IN ...
Page 12
... Figure 5b: Open load: detection in ON- and OFF-state (with R ), turn on/off to open load EXT OUT I L open load I IS Figure 6a: Undervoltage bb(under Infineon Technologies AG Figure 6b: Undervoltage restart of charge pump d(ST OL3) V bb(u rst) V bb(under) t charge pump starts at V Figure 7a: Overvoltage not defined bb(u cp) V bb(u rst) ...
Page 13
... ILIS 10000 5000 This range for the current sense ratio refers to all devices. The accuracy of the k least by a factor of two by matching the value of k for every single device. ILIS Infineon Technologies AG Figure 9a: Output voltage drop versus load current: [V] 0.2 0 0.0 [ ...
Page 14
... Published by Infineon Technologies AG, St.-Martin-Strasse 53, D-81669 München ITS640S2 © Infineon Technologies AG 2006 All Rights Reserved. SP000221217 Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. 4.4 Terms of delivery and rights to technical change reserved. 1.27 ± ...