ADV7343BSTZ Analog Devices Inc, ADV7343BSTZ Datasheet - Page 51

• Manufacturer Part Number: ADV7343BSTZ
• Description: IC ENCODER VIDEO W/DAC 64-LQFP
• Manufacturer: Analog Devices Inc
• Type: Video Encoderr

Specifications of ADV7343BSTZ

• Applications: DVD, Blu-Ray
• Voltage - Supply, Analog: 3.3V
• Voltage - Supply, Digital: 1.8V
• Mounting Type: Surface Mount
• Package / Case: 64-LQFP
• Supply Voltage Range: 1.71V To 1.89V
• Operating Temperature Range: -40°C To +85°C
• Tv / Video Case Style: LQFP
• No. Of Pins: 64
• Svhc: No SVHC (18-Jun-2010)
• Operating Temperature Max: 85°C
• Operating: RoHS Compliant
• Input Format: Digital
• Output Format: Analogue
• Dac Resolution: 11bit
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

HD INTERLACE EXTERNAL P_HSYNC AND
P_VSYNC CONSIDERATIONS
If the encoder revision code (Subaddress 0xBB, Bits[7:6]) = 01
or higher, the user should set Subaddress 0x02, Bit 1 to high to
ensure exactly correct timing in HD interlace modes when
using the P_HSYNC and P_VSYNC synchronization signals. If
this bit is set to low, the first active pixel on each line is masked
and the Pr and Pb outputs are swapped when using the YCrCb
4:2:2 input format. Setting Subaddress 0x02, Bit 1 to low causes
the encoder to behave in the same way as the first version of
silicon (that is, this setting is backward compatible).
If the encoder revision code (Subaddress 0xBB, Bits[7:6] = 00,
the setting of Subaddress 0x02, Bit1 has no effect. In this version
of the encoder, the first active pixel is masked and Pr and Pb
outputs are swapped when using the YCrCb 4:2:2 input format.
To avoid these limitations, use the newer version of silicon or a
different type of synchronization.
These considerations apply only to the HD interlace modes
with external P_HSYNC and P_VSYNC synchronization
(EAV/SAV mode is not affected and always has exactly correct
timing). There is no negative effect in setting Subaddress 0x02,
Bit 0 to high, and this bit can remain high for all the other video
standards.
ED/HD TIMING RESET
Subaddress 0x34, Bit 0
An ED/HD timing reset is achieved by toggling the ED/HD
timing reset control bit (Subaddress 0x34, Bit 0) from 0 to 1.
In this state, the horizontal and vertical counters remain reset.
When this bit is set back to 0, the internal counters resume
counting. This timing reset applies to the ED/HD timing
counters only.
SD SUBCARRIER FREQUENCY LOCK, SUBCARRIER
PHASE RESET, AND TIMING RESET
Subaddress 0x84, Bits[2:1]
Together with the SFL pin and SD Mode Register 4 (Subaddress
0x84, Bits[2:1]), the ADV7342/ADV7343 can be used in timing
reset mode, subcarrier phase reset mode, or SFL mode.
DISPLAY
307
NO TIMING RESET APPLIED
TIMING RESET APPLIED
307
DISPLAY
Figure 60. SD Timing Reset Timing Diagram (Subaddress 0x84, Bits [2:1] = 10)
310
1
START OF FIELD 1
2
3
313
4
START OF FIELD 4 OR 8
Rev. A | Page 51 of 104
5
6
F
7
SC
Timing Reset (TR) Mode
In this mode (Subaddress 0x84, Bits[2:1] = 10), a timing reset is
achieved in a low-to-high transition on the SFL pin (Pin 48). In
this state, the horizontal and vertical counters remain reset.
Upon releasing this pin (set to low), the internal counters resume
counting, starting with Field 1, and the subcarrier phase is reset.
The minimum time the pin must be held high is one clock
cycle; otherwise, this reset signal may not be recognized. This
timing reset applies to the SD timing counters only.
Subcarrier Phase Reset (SCR) Mode
In this mode (Subaddress 0x84, Bits[2:1] = 01), a low-to-high
transition on the SFL pin (Pin 48) resets the subcarrier phase to
0 on the field following the subcarrier phase reset. This reset
signal must be held high for a minimum of one clock cycle.
Because the field counter is not reset, it is recommended that
the reset signal be applied in Field 7 (PAL) or Field 3 (NTSC).
The reset of the phase then occurs on the next field, that is,
Field 1, lined up correctly with the internal counters. The field
count register at Subaddress 0xBB can be used to identify the
number of the active field.
Subcarrier Frequency Lock (SFL) Mode
In this mode (Subaddress 0x84, Bits[2:1] = 11), the ADV7342/
ADV7343 can be used to lock to an external video source. The
SFL mode allows the ADV7342/ADV7343 to automatically alter
the subcarrier frequency to compensate for line length variations.
When the part is connected to a device such as an
video decoder (see Figure 62) that outputs a digital data stream
in the SFL format, the part automatically changes to the com-
pensated subcarrier frequency on a line-by-line basis. This
digital data stream is 67 bits wide, and the subcarrier is
contained in Bit 0 to Bit 21. Each bit is two clock cycles long.
PHASE = FIELD 1
21
F
320
SC
PHASE = FIELD 4 OR 8
TIMING RESET PULSE
ADV7342/ADV7343
ADV7403