EPM9560RC208-20 Altera, EPM9560RC208-20 Datasheet - Page 29

• Manufacturer Part Number: EPM9560RC208-20
• Manufacturer: Altera

Specifications of EPM9560RC208-20

• Family Name: MAX 9000
• Memory Type: EEPROM
• # Macrocells: 560
• Number Of Usable Gates: 12000
• Frequency (max): 100MHz
• Propagation Delay Time: 20ns
• Number Of Logic Blocks/elements: 35
• # I/os (max): 153
• Operating Supply Voltage (typ): 5V
• In System Programmable: Yes
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: RQFP
• Lead Free Status / Rohs Status: Not Compliant

Notes to tables:
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10) Capacitance is sample-tested only and is measured at 25 C.
(11) Measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB. I
Figure 13. Output Drive Characteristics of MAX 9000 Devices
Note:
(1)
Altera Corporation
Symbol
I
Typical I
Output
Current (mA)
CC1
5.0-V
Table 20. MAX 9000A Device Typical I
See the
Minimum DC input on I/O pins is –0.5 V and on the four dedicated input pins is –0.3 V. During transitions, the
inputs may undershoot to –2.0 V or overshoot to 7.0 V for periods shorter than 20 ns under no-load conditions.
V
Numbers in parentheses are for industrial-temperature-range devices.
Typical values are for T
These values are specified under the MAX 9000 recommended operating conditions, shown in
During in-system programming, the minimum V
during JTAG testing remains at 2.0 V. To attain this 3.6-V V
ByteBlasterMV download cables must have a 5.0-V V
This parameter is measured with 50% of the outputs each sinking 12 mA. The I
TTL or CMOS output current; the I
JTAG pin input leakage is typically –60
Output drive characteristics include the JTAG TDO pin.
CC
O
must rise monotonically.
I
standby, typical)
CC
150
120
Operating Requirements for Altera Devices Data
90
60
30
supply current (low-power mode,
Parameter
1
Output Voltage (V)
A
2
= 25 C and V
Figure 13
with 5.0-V and 3.3-V V
V
Room Temperature
I
I
OH
3
OL
CCIO
OL
= 5.0 V
parameter refers to the low-level TTL or CMOS output current.
shows typical output drive characteristics for MAX 9000 devices
4
CC
CC
V
Supply Current Values
I
.
= 5.0 V.
= ground, no load
5
MAX 9000 Programmable Logic Device Family Data Sheet
IH
of the JTAG TCK pin is 3.6 V. The minimum V
Sheet.
CC
CCIO
Conditions
.
3.3-V
Typical I
Output
Current (mA)
IH
.
(11)
during programming, the ByteBlaster and
O
Note (1)
150
120
90
60
30
1
OH
EPM9320A EPM9560A Unit
parameter refers to high-level
Output Voltage (V)
2
99
V
Room Temperature
I
I
CC
OH
3
OL
CCIO
3.3
Table 15 on page
is measured at 0 C.
= 3.3 V
IH
4
174
of this pin
5
mA
27.
29