LPC1754FBD80,518 NXP Semiconductors, LPC1754FBD80,518 Datasheet - Page 19

• Manufacturer Part Number: LPC1754FBD80,518
• Description: IC MCU 32BIT 128KB FLASH 80LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1754FBD80,518

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: CAN, I²C, IrDA, Microwire, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 52
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 6x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-LQFP
• Package: 80LQFP
• Device Core: ARM Cortex M3
• Family Name: LPC1700
• Maximum Speed: 100 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 52
• Interface Type: CAN/I2C/SPI/UART/USB
• On-chip Adc: 6-chx12-bit
• Number Of Timers: 4
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

NXP Semiconductors
LPC1759_58_56_54_52_51
Product data sheet
7.12.1.1 Features
7.12.1 USB device controller
7.12 USB interface
The Universal Serial Bus (USB) is a 4-wire bus that supports communication between a
host and one or more (up to 127) peripherals. The host controller allocates the USB
bandwidth to attached devices through a token-based protocol. The bus supports hot
plugging and dynamic configuration of the devices. All transactions are initiated by the
host controller.
The LPC1759/58/56/54 USB interface includes a device, Host, and OTG controller with
on-chip PHY for device and Host functions. The OTG switching protocol is supported
through the use of an external controller. Details on typical USB interfacing solutions can
be found in
The device controller enables 12 Mbit/s data exchange with a USB Host controller. It
consists of a register interface, serial interface engine, endpoint buffer memory, and a
DMA controller. The serial interface engine decodes the USB data stream and writes data
to the appropriate endpoint buffer. The status of a completed USB transfer or error
condition is indicated via status registers. An interrupt is also generated if enabled. When
enabled, the DMA controller transfers data between the endpoint buffer and the on-chip
SRAM.
•
•
•
•
•
•
•
– Receive filtering.
– Multicast and broadcast frame support for both transmit and receive.
– Optional automatic Frame Check Sequence (FCS) insertion with Cyclic
– Selectable automatic transmit frame padding.
– Over-length frame support for both transmit and receive allows any length frames.
– Promiscuous receive mode.
– Automatic collision back-off and frame retransmission.
– Includes power management by clock switching.
– Wake-on-LAN power management support allows system wake-up: using the
Physical interface:
– Attachment of external PHY chip through standard RMII interface.
– PHY register access is available via the MIIM interface.
Fully compliant with USB 2.0 specification (full speed).
Supports 32 physical (16 logical) endpoints with a 4 kB endpoint buffer RAM.
Supports Control, Bulk, Interrupt and Isochronous endpoints.
Scalable realization of endpoints at run time.
Endpoint Maximum packet size selection (up to USB maximum specification) by
software at run time.
Supports SoftConnect and GoodLink features.
Redundancy Check (CRC) for transmit.
receive filters or a magic frame detection filter.
Section
All information provided in this document is subject to legal disclaimers.
14.1. The LPC1752/51 include a USB device controller only.
Rev. 7 — 29 March 2011
LPC1759/58/56/54/52/51
32-bit ARM Cortex-M3 microcontroller
© NXP B.V. 2011. All rights reserved.
19 of 74