C8051F317-GMR Silicon Laboratories Inc, C8051F317-GMR Datasheet - Page 215

• Manufacturer Part Number: C8051F317-GMR
• Description: MCU 8-Bit C8051F31x 8051 CISC 16KB Flash 3.3V 24-Pin QFN EP T/R
• Manufacturer: Silicon Laboratories Inc

Specifications of C8051F317-GMR

• Package: 24QFN EP
• Device Core: 8051
• Family Name: C8051F31x
• Maximum Speed: 25 MHz
• Ram Size: 1.25 KB
• Program Memory Size: 16 KB
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 8 Bit
• Program Memory Type: Flash
• Number Of Programmable I/os: 21
• Interface Type: I2C/SMBus/SPI/UART
• On-chip Adc: 17-chx10-bit
• Operating Temperature: -40 to 85 °C
• Number Of Timers: 4

18.4. Register Descriptions for PCA
Following are detailed descriptions of the special function registers related to the operation of the PCA.
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
R/W
CF
Bit7
CF: PCA Counter/Timer Overflow Flag.
Set by hardware when the PCA Counter/Timer overflows from 0xFFFF to 0x0000. When the
Counter/Timer Overflow (CF) interrupt is enabled, setting this bit causes the CPU to vector
to the PCA interrupt service routine. This bit is not automatically cleared by hardware and
must be cleared by software.
CR: PCA Counter/Timer Run Control.
This bit enables/disables the PCA Counter/Timer.
0: PCA Counter/Timer disabled.
1: PCA Counter/Timer enabled.
UNUSED. Read = 0b, Write = don't care.
CCF4: PCA Module 4 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF4 interrupt is
enabled, setting this bit causes the CPU to vector to the PCA interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
CCF3: PCA Module 3 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF3 interrupt is
enabled, setting this bit causes the CPU to vector to the PCA interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
CCF2: PCA Module 2 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF2 interrupt is
enabled, setting this bit causes the CPU to vector to the PCA interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
CCF1: PCA Module 1 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF1 interrupt is
enabled, setting this bit causes the CPU to vector to the PCA interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
CCF0: PCA Module 0 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF0 interrupt is
enabled, setting this bit causes the CPU to vector to the PCA interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
R/W
CR
Bit6
SFR Definition 18.1. PCA0CN: PCA Control
R/W
Bit5
CCF4
R/W
Bit4
Rev. 1.7
CCF3
R/W
Bit3
C8051F310/1/2/3/4/5/6/7
CCF2
R/W
Bit2
CCF1
R/W
Bit1
(bit addressable)
CCF0
R/W
Bit0
SFR Address:
00000000
Reset Value
0xD8
215