PEF 2054 N V2.1 Infineon Technologies, PEF 2054 N V2.1 Datasheet - Page 203
PEF 2054 N V2.1
Manufacturer Part Number
PEF 2054 N V2.1
Description
IC INTERFACE CTRLR PCM LCC-44
Manufacturer
Infineon Technologies
Series
EPICr
Datasheet
1.PEF_2054_N_V2.1.pdf
(269 pages)
Specifications of PEF 2054 N V2.1
Function
PCM Interface Controller
Interface
ISDN, PCM
Number Of Circuits
1
Voltage - Supply
5V
Current - Supply
9.5mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
44-LCC
Includes
Board Controller, Channel Switching
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power (watts)
-
Other names
PEF2054NV2.1XT
PEF2054NV21XK
SP000057916
SP000075438
PEF2054NV21XK
SP000057916
SP000075438
- Current page: 203 of 269
- Download datasheet (2Mb)
PEB 2055
PEF 2055
Application Hints
This command can also be used to perform a receive only operation: if a message shall
be received without transmission (e.g. after an active monitor channel has been found)
the transmit + receive command is issued with an empty MFFIFO.
The command is applicable for both handshake and non-handshake protocols. Since the
transfer operation is performed on the same time slot, its use is intended for IOM
applications:
– IOM-2, handshake facility enabled:
The contents of the MFFIFO is sent to the subscriber circuit subject to the IOM-2 protocol
i.e each byte must be acknowledged before the next one is sent. When the MFFIFO is
empty, the EPIC starts to receive the incoming data bytes, each byte being
autonomously acknowledged by the EPIC. Up to 16 bytes may be stored in the MFFIFO.
When the end of message is detected (MX bit inactive during two consecutive frames),
the transfer is considered terminated and an ISTA:MFFI interrupt is generated. The P
can then fetch the message from the MFFIFO. In order to determine the length of the
arrived message, the STAR:MFFE bit (MFFIFO Empty) should be evaluated before each
read access to the MFFIFO. After all bytes have been read, the MFFIFO must be reset
with the CMDR:MFFR command in order to enable new monitor transfer operations.
Semiconductor Group
203
Related parts for PEF 2054 N V2.1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC NETWORK TERMINATOR PDSO-20
Manufacturer:
Infineon Technologies
Part Number:
Description:
IC NETWORK TERMINATOR PDSO-20
Manufacturer:
Infineon Technologies
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
16-bit microcontroller with 2x2 KByte RAM
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
NPN silicon RF transistor
Manufacturer:
Infineon Technologies AG
Datasheet:
Part Number:
Description:
Si-MMIC-amplifier in SIEGET 25-technologie
Manufacturer:
Infineon Technologies AG
Datasheet: