AT32UC3B0256 Atmel Corporation, AT32UC3B0256 Datasheet - Page 120

• Manufacturer Part Number: AT32UC3B0256
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0256

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

14. Flash Controller (FLASHC)
14.1
14.2
14.3
14.3.1
14.3.2
32059L–AVR32–01/2012
Features
Overview
Product dependencies
Power Manager
Interrupt Controller
Rev: 2.1.2.4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The flash controller (FLASHC) interfaces a flash block with the 32-bit internal High-Speed Bus
(HSB). Performance for uncached systems with high clock-frequency and one wait state is
increased by placing words with sequential addresses in alternating flash subblocks. Having one
read interface per subblock allows them to be read in parallel. While data from one flash sub-
block is being output on the bus, the sequential address is being read from the other flash
subblock and will be ready in the next clock cycle.
The controller also manages the programming, erasing, locking and unlocking sequences with
dedicated commands.
The FLASHC has two bus clocks connected: One High speed bus clock (CLK_FLASHC_HSB)
and one Peripheral bus clock (CLK_FLASHC_PB). These clocks are generated by the Power
manager. Bot h clocks are turned on by default, but the user has t o ensure that
CLK_FLASHC_HSB is not turned off before reading the flash or writing the pagebuffer and that
CLK_FLASHC_PB is not turned off before accessing the FLASHC configuration and control
registers.
The FLASHC interrupt lines are connected to internal sources of the interrupt controller. Using
FLASHC interrupts requires the interrupt controller to be programmed first.
Controls flash block with dual read ports allowing staggered reads.
Supports 0 and 1 wait state bus access.
Allows interleaved burst reads for systems with one wait state, outputting one 32-bit word per
clock cycle.
32-bit HSB interface for reads from flash array and writes to page buffer.
32-bit PB interface for issuing commands to and configuration of the controller.
16 lock bits, each protecting a region consisting of (total number of pages in the flash block / 16)
pages.
Regions can be individually protected or unprotected.
Additional protection of the Boot Loader pages.
Supports reads and writes of general-purpose NVM bits.
Supports reads and writes of additional NVM pages.
Supports device protection through a security bit.
Dedicated command for chip-erase, first erasing all on-chip volatile memories before erasing
flash and clearing security bit.
Interface to Power Manager for power-down of flash-blocks in sleep mode.
120