AT32UC3B0256 Atmel Corporation, AT32UC3B0256 Datasheet - Page 364

• Manufacturer Part Number: AT32UC3B0256
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0256

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32059L–AVR32–01/2012
U(P/E)RST.(E)PENn = 1
U(P/E)CFGn.ALLOC = 1
Pipes/Endpoints 0..5
Free Memory
Activated
memory area in the DPRAM and inserts it between the n-1 and n+1 pipes/endpoints. The n+1
pipe/endpoint memory window slides up and its data is lost. Note that the following pipe/end-
point memory windows (from n+2) do not slide.
Disabling a pipe, by writing a zero to the Pipe n Enable bit in the Pipe Enable/Reset register
(UPRST.PENn), or disabling an endpoint, by writing a zero to the Endpoint n Enable bit in the
Endpoint Enable/Reset register (UERST.EPENn), resets neither the UECFGn.ALLOC bit nor its
configuration (the Pipe Banks (PBK) field, the Pipe Size (PSIZE) field, the Pipe Token (PTO-
KEN) field, the Pipe Type (PTYPE) field, the Pipe Endpoint Number (PEPNUM) field, and the
Pipe Interrupt Request Frequency (INTFRQ) field in the Pipe n Configuration (UPCFGn) regis-
ter/the Endpoint Banks (EPBK) field, the Endpoint Size (EPSIZE) field, the Endpoint Direction
(EPDIR) field, and the Endpoint Type (EPTYPE) field in UECFGn).
To free its memory, the user shall write a zero to the UECFGn.ALLOC bit. The n+1 pipe/end-
point memory window then slides down and its data is lost. Note that the following pipe/endpoint
memory windows (from n+2) does not slide.
Figure 22-8 on page 364
example.
Figure 22-8. Allocation and Reorganization of the DPRAM
Note that:
PEP5
PEP4
PEP3
PEP2
PEP1
PEP0
1. The pipes/endpoints 0 to 5 are enabled, configured and allocated in ascending order.
2. The pipe/endpoint 3 is disabled, but its memory is kept allocated by the controller.
3. In order to free its memory, its ALLOC bit is written to zero. The pipe/endpoint 4 mem-
4. If the user chooses to reconfigure the pipe/endpoint 3 with a larger size, the controller
Each pipe/endpoint then owns a memory area in the DPRAM.
ory window slides down, but the pipe/endpoint 5 does not move.
allocates a memory area after the pipe/endpoint 2 memory area and automatically
slides up the pipe/endpoint 4 memory window. The pipe/endpoint 5 does not move and
a memory conflict appears as the memory windows of the pipes/endpoints 4 and 5
overlap. The data of these pipes/endpoints is potentially lost.
U(P/E)RST.(E)PEN3 = 0
Pipe/Endpoint 3
(ALLOC stays at 1)
Free Memory
Disabled
PEP5
PEP4
PEP3
PEP2
PEP1
PEP0
illustrates the allocation and reorganization of the DPRAM in a typical
U(P/E)CFG3.ALLOC = 0
Pipe/Endpoint 3
PEP4 Lost Memory
Memory Freed
Free Memory
PEP5
PEP4
PEP2
PEP1
PEP0
U(P/E)RST.(E)PEN3 = 1
U(P/E)CFG3.ALLOC = 1
Pipe/Endpoint 3
PEP3 (larger size)
Free Memory
Activated
PEP4
PEP2
PEP1
PEP0
PEP5
Conflict
364