AT32UC3B0512AU Atmel Corporation, AT32UC3B0512AU Datasheet - Page 173

• Manufacturer Part Number: AT32UC3B0512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

17.5.1
17.5.1.1
17.5.1.2
17.5.1.3
32059L–AVR32–01/2012
Basic Operation
Output control
I/O Line or peripheral function selection
Peripheral selection
Figure 17-2. Overview of the GPIO Pad Connections
When a pin is multiplexed with one or more peripheral functions, the selection is controlled with
the GPIO Enable Register (GPER). If a bit in GPER is written to one, the corresponding pin is
controlled by the GPIO. If a bit is written to zero, the corresponding pin is controlled by a periph-
eral function.
The GPIO provides multiplexing of up to four peripheral functions on a single pin. The selection
is performed by accessing Peripheral Mux Register 0 (PMR0) and Peripheral Mux Register 1
(PMR1).
When the I/O line is assigned to a peripheral function, i.e. the corresponding bit in GPER is writ-
ten to zero, the drive of the I/O line is controlled by the peripheral. The peripheral, depending on
the value in PMR0 and PMR1, determines whether the pin is driven or not.
When the I/O line is controlled by the GPIO, the value of the Output Driver Enable Register
(ODER) determines if the pin is driven or not. When a bit in this register is written to one, the cor-
Periph. A output enable
Periph. B output enable
Periph. C output enable
Periph. D output enable
Periph. A output data
Periph. B output data
Periph. C output data
Periph. D output data
Periph. A input data
Periph. B input data
Periph. C input data
Periph. D input data
PMR1
PMR0
ODER
OVR
GPER
Glitch Filter
PVR
GFER
1
0
0
1
0
1
Edge Detector
IMR1
IMR0
IER
1
0
PUER
Interrupt Request
PAD
173