AT32UC3B0512AU Atmel Corporation, AT32UC3B0512AU Datasheet - Page 203

• Manufacturer Part Number: AT32UC3B0512AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3B0512AU

• Flash (kbytes): 512 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 60 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 44
• Ext Interrupts: 44
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 4
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 96
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 18-8. Peripheral Deselection
18.7.3.8
32059L–AVR32–01/2012
Write SPI_TDR
Write SPI_TDR
Write SPI_TDR
NPCS[0..3]
NPCS[0..3]
NPCS[0..3]
TDRE
TDRE
TDRE
Mode Fault Detection
A
A
A
to an interrupt, and thus might lead to difficulties for interfacing with some serial peripherals
requiring the chip select line to remain active during a full set of transfers.
To facilitate interfacing with such devices, the Chip Select Register can be programmed with the
CSAAT bit (Chip Select Active After Transfer) at 1. This allows the chip select lines to remain in
their current state (low = active) until transfer to another peripheral is required.
Figure 18-8 on page 203
CSAAT bits.
A mode fault is detected when the SPI is programmed in Master Mode and a low level is driven
by an external master on the NPCS0/NSS signal. NPCS0, MOSI, MISO and SPCK must be con-
figured in open drain through the GPIO controller, so that external pull up resistors are needed to
guarantee high level.
When a mode fault is detected, the MODF bit in the SR is set until the SR is read and the SPI is
automatically disabled until re-enabled by writing the SPIEN bit in the CR (Control Register) at 1.
By default, the Mode Fault detection circuitry is enabled. The user can disable Mode Fault
detection by setting the MODFDIS bit in the SPI Mode Register (MR).
DLYBCT
DLYBCT
DLYBCT
CSAAT = 0
DLYBCS
DLYBCS
DLYBCS
PCS = B
PCS=A
PCS = A
A
B
shows different peripheral deselection cases and the effect of the
A
A
A
A
DLYBCT
DLYBCT
DLYBCT
CSAAT = 1
DLYBCS
DLYBCS
PCS = B
PCS = A
A
A
PCS = A
DLYBCS
A
A
B
203