ATmega8515 Atmel Corporation, ATmega8515 Datasheet - Page 110

no-image

ATmega8515

Manufacturer Part Number
ATmega8515
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega8515

Flash (kbytes)
8 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
35
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
3
Input Capture Channels
1
Pwm Channels
3
32khz Rtc
No
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA8515
Manufacturer:
ATMEL
Quantity:
5 510
Part Number:
ATMEGA8515
Manufacturer:
NS
Quantity:
5 510
Part Number:
ATMEGA8515
Manufacturer:
AT
Quantity:
20 000
Part Number:
ATmega8515-16AC
Manufacturer:
MOT
Quantity:
3 450
Part Number:
ATmega8515-16AC
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16AC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16AI
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16AI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16AJ
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16AU
Manufacturer:
ATMEL
Quantity:
4 500
Part Number:
ATmega8515-16AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega8515-16AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega8515-16JU
Quantity:
1 831
Part Number:
ATmega8515-16PU
Manufacturer:
AT
Quantity:
20 000
Clear Timer on Compare
Match (CTC) Mode
110
ATmega8515(L)
In clear timer on compare or CTC mode (WGM13:0 = 4 or 12), the OCR1A or ICR1 Reg-
ister are used to manipulate the counter resolution. In CTC mode the counter is cleared
to zero when the counter value (TCNT1) matches either the OCR1A (WGM13:0 = 4) or
the ICR1 (WGM13:0 = 12). The OCR1A or ICR1 define the top value for the counter,
hence also its resolution. This mode allows greater control of the Compare Match output
frequency. It also simplifies the operation of counting external events.
The timing diagram for the CTC mode is shown in Figure 52. The counter value
(TCNT1) increases until a Compare Match occurs with either OCR1A or ICR1, and then
counter (TCNT1) is cleared.
Figure 52. CTC Mode, Timing Diagram
An interrupt can be generated at each time the counter value reaches the TOP value by
either using the OCF1A or ICF1 Flag according to the register used to define the TOP
value. If the interrupt is enabled, the interrupt handler routine can be used for updating
the TOP value. However, changing the TOP to a value close to BOTTOM when the
counter is running with none or a low prescaler value must be done with care since the
CTC mode does not have the double buffering feature. If the new value written to
OCR1A or ICR1 is lower than the current value of TCNT1, the counter will miss the
Compare Match. The counter will then have to count to its maximum value (0xFFFF)
and wrap around starting at 0x0000 before the Compare Match can occur. In many
cases this feature is not desirable. An alternative will then be to use the fast PWM mode
using OCR1A for defining TOP (WGM13:0 = 15) since the OCR1A then will be double
buffered.
For generating a waveform output in CTC mode, the OC1A output can be set to toggle
its logical level on each Compare Match by setting the Compare Output mode bits to
toggle mode (COM1A1:0 = 1). The OC1A value will not be visible on the port pin unless
the data direction for the pin is set to output (DDR_OC1A = 1). The waveform generated
will have a maximum frequency of f
The waveform frequency is defined by the following equation:
The N variable represents the prescaler factor (1, 8, 64, 256, or 1024).
As for the normal mode of operation, the TOV1 Flag is set in the same timer clock cycle
that the counter counts from MAX to 0x0000.
TCNTn
OCnA
(Toggle)
Period
1
f
OCnA
2
OC
=
1
A
-------------------------------------------------- -
2 N
= f
clk_I/O
3
(
f
1
clk_I/O
/2 when OCR1A is set to zero (0x0000).
+
OCRnA
4
)
OCnA Interrupt Flag Set
or ICFn Interrupt Flag Set
(Interrupt on TOP)
(COMnA1:0 = 1)
2512K–AVR–01/10

Related parts for ATmega8515