ATUC64L4U Atmel Corporation, ATUC64L4U Datasheet - Page 97

• Manufacturer Part Number: ATUC64L4U
• Manufacturer: Atmel Corporation

Specifications of ATUC64L4U

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 50 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: Yes
• Max I/o Pins: 36
• Ext Interrupts: 36
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 460
• Analog Comparators: 8
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.62 to 3.6
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 35
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8.6.2.15
32142A–12/2011
RXOUTI
FIFOCON
OUT
Management of OUT endpoints
• Overview
(bank 0)
DATA
set, or if the total byte count is not an integral multiple of EPSIZE, whereby the last packet
should be short.
To enable the multi packet mode, the user should configure the endpoint descriptor
(EPn_PCKSIZE_BK0/1.BYTE_COUNT) to the total size of the multi packet, which should be
larger than the endpoint size (EPSIZE).
Since the EPn_PCKSIZE_BK0/1.MULTI_PACKET_SIZE is incremented (by the transmitted
packet size) after each successful transaction, it should be set to zero when setting up a new
multi packet transfer.
The EPn_PCKSIZE_BK0/1.MULTI_PACKET_SIZE is cleared by hardware when all the bank
contents have been sent. The bank is considered as ready and the TX_IN flag is set when:
The endpoint and its descriptor in RAM must be pre configured, see section
on page 90
When the current bank is full, the RXOUTI and FIFO Control (UECONn.FIFOCON) bits will be
set simultaneously. This triggers an EPnINT interrupt if the Received OUT Data Interrupt Enable
(RXOUTE) bit in UECONn is one.
RXOUTI shall be cleared by software (by writing a one to the Received OUT Data Interrupt Clear
(RXOUTIC) bit) to acknowledge the interrupt. This has no effect on the endpoint FIFO.
The user reads the OUT data from the RAM and clears the FIFOCON bit to free the bank. This
will also cause a switch to the next bank if the OUT endpoint is composed of multiple banks.
RXOUTI should always be cleared before clearing FIFOCON to avoid missing an RXOUTI
event.
Figure 8-11. Example of an OUT endpoint with one data bank
• A short packet (smaller than EPSIZE) has been transmitted.
• A packet has been successfully transmitted, the updated MULTI_PACKET_SIZE equals the
• An extra zero length packet has been automatically sent for the last transfer of the current
BYTE_COUNT, and the AUTO_ZLP field is not set.
bank, if BYTE_COUNT is a multiple of EPSIZE and AUTO_ZLP is set.
HW
ACK
for more details.
SW
read data from CPU
BANK 0
NAK
SW
OUT
ATUC64/128/256L3/4U
(bank 0)
DATA
HW
ACK
”RAM management”
read data from CPU
SW
BANK 0
97