ATxmega16D4 Atmel Corporation, ATxmega16D4 Datasheet - Page 256

• Manufacturer Part Number: ATxmega16D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega16D4

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8210B–AVR–04/10
Table 21-6.
• Bit 5 - AC1STATE: Analog Comparator 1 Current State
This bit shows the current state of the input signal to Analog Comparator 1.
• Bit 4 - AC0STATE: Analog Comparator 0 Current State
This bit shows the current state of the input signal to Analog Comparator 0.
• Bit 3 - Reserved
This bit is unused and reserved for future use. For compatibility with future devices, always write
this bit to zero when this register is written.
• Bit 2 - WIF: Analog Comparator Window Interrupt Flag
This is the interrupt flag for the Window Mode. WIF is set according to the WINTMODE setting in
the
The WIF is automatically cleared when the analog comparator window interrupt vector is exe-
cuted. The flag can also be cleared by writing a one to its bit location.
• Bit 1 - AC1IF: Analog Comparator 1 Interrupt Flag
This is the interrupt flag for Analog Comparator 1. AC1IF is set according to the INTMODE set-
ting in the corresponding
The AC1IF is automatically cleared when the analog comparator 1 interrupt vector is executed.
The flag can also be cleared by writing a one to its bit location.
• Bit 0 - AC0IF: Analog Comparator 0 Interrupt Flag
This is the interrupt flag for Analog Comparator 0. AC0IF is set according to the INTMODE set-
ting in the corresponding
The AC0IF is automatically cleared when the analog comparator interrupt vector is executed.
The flag can also be cleared by writing a one to its bit location.
”WINCTRL – Analog Comparator Window Function Control Register” on page
WSTATE[1:0]
00
01
10
11
Analog Comparator Window Mode Current State
Group Configuration
”ACnCTRL – Analog Comparator n Control Register” on page
”ACnCTRL – Analog Comparator n Control Register” on page
BELOW
ABOVE
INSIDE
-
Signal is inside window
Description
Signal is above window
Signal is below window
Reserved
XMEGA D
255.
252.
252.
256