ATxmega64A1 Atmel Corporation, ATxmega64A1 Datasheet - Page 43
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATxmega64A1
Manufacturer Part Number
ATxmega64A1
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega64A1
Flash (kbytes)
64 Kbytes
Pin Count
100
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
78
Ext Interrupts
78
Usb Speed
No
Usb Interface
No
Spi
12
Twi (i2c)
4
Uart
8
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
4
Resistive Touch Screen
No
Dac Channels
4
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
AES/DES
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
External Bus Interface
1
Dram Memory
sdram
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
8
Output Compare Channels
24
Input Capture Channels
24
Pwm Channels
24
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATxmega64A1-AU
Manufacturer:
Atmel
Quantity:
135
Company:
Part Number:
ATxmega64A1U-AU
Manufacturer:
ATMEL
Quantity:
953
25. DAC - 12-bit Digital to Analog Converter
25.1
25.2
8067M–AVR–09/10
Features
Overview
•
•
•
•
•
•
•
•
The XMEGA A1 devices features two 12-bit, 1 Msps DACs with built-in offset and gain calibra-
tion, see
A DAC converts a digital value into an analog signal. The DAC may use an internal 1.0 voltage
as the upper limit for conversion, but it is also possible to use the supply voltage or any applied
voltage in-between. The external reference input is shared with the ADC reference input.
Figure 25-1. DAC overview
Each DAC has one continuous output with high drive capabilities for both resistive and capaci-
tive loads. It is also possible to split the continuous time channel into two Sample and Hold (S/H)
channels, each with separate data conversion registers.
A DAC conversion may be started from the application software by writing the data conversion
registers. The DAC can also be configured to do conversions triggered by the Event System to
have regular timing, independent of the application software. DMA may be used for transferring
data from memory locations to DAC data registers.
The DAC has a built-in calibration system to reduce offset and gain error when loading with a
calibration value from software.
PORTA and PORTB each has one DAC. Notation of these peripherals are DACA and DACB.
respectively.
Two DACs with 12-bit resolution
Up to 1 Msps conversion rate for each DAC
Flexible conversion range
Multiple trigger sources
1 continuous output or 2 Sample and Hold (S/H) outputs for each DAC
Built-in offset and gain calibration
High drive capabilities
Low Power Mode
Figure 25-1 on page
Channel A
Channel B
Register
Register
43.
Reference selection
Configuration
Trigger
DAC
Event
Channel A
Channel B
XMEGA A1
43