ATxmega64A1 Atmel Corporation, ATxmega64A1 Datasheet - Page 96

• Manufacturer Part Number: ATxmega64A1
• Manufacturer: Atmel Corporation

Specifications of ATxmega64A1

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 78
• Ext Interrupts: 78
• Usb Speed: No
• Usb Interface: No
• Spi: 12
• Twi (i2c): 4
• Uart: 8
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 4
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 8
• Output Compare Channels: 24
• Input Capture Channels: 24
• Pwm Channels: 24
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8067M–AVR–09/10
28. Flash Power Reduction Mode can not be enabled when entering sleep
29. Some NVM Commands are non-functional
30. Crystal start-up time required after power-save even if crystal is source for RTC
31. Setting PRHIRES bit makes PWM output unavailable
32. Accessing EBI address space with PREBI set will lock Bus Master
If Flash Power Reduction Mode is enabled when entering Power-save or Extended Standby
sleep mode, the device will only wake up on every fourth wake-up request. If Flash Power
Reduction Mode is enabled when entering Idle sleep mode, the wake-up time will vary with
up to 16 CPU clock cycles.
Problem fix/Workaround
Disable Flash Power Reduction mode before entering sleep mode.
The following NVM commands are non-functional:
Problem fix/Workaround
None for Flash Range CRC
Use separate programming commands for accessing application and boot section.
Even if 32.768 kHz crystal is used for RTC during sleep, the clock from the crystal will not be
ready for the system before the specified start-up time. See "XOSCSEL[3:0]: Crystal Oscilla-
tor Selection" in XMEGA A Manual. If BOD is used in active mode, the BOD will be on during
this period (0.5s).
Problem fix/Workaround
If faster start-up is required, go to sleep with internal oscillator as system clock.
Setting the HIRES Power Reduction (PR) bit for PORTx will make any Frequency or PWM
output for the corresponding Timer/Counters (TCx0 and TCx1) unavailable on the pin even if
the Hi-Res is not used.
Problem fix/Workaround
Do not write the HIRES PR bit on PORTx when frequency or PWM output from TCx0/1 is
used.
–
–
–
–
–
–
–
–
–
–
0x2C
0x2D
0x2B
0x2E
0x3A
0x2A
0x2F
0x22
0x24
0x25
Erase Flash Page
Write Flash Page
Erase & Write Flash Page
Flash Range CRC
Erase Application Section Page
Write Application Section Page
Erase & Write Application Section Page
Erase Boot Loader Section Page
Write Boot Loader Section Page
Erase & Write Boot Loader Section Page
XMEGA A1
96