AD9211 Analog Devices, AD9211 Datasheet - Page 19

• Manufacturer Part Number: AD9211
• Description: 10-Bit, 200 MSPS/250 MSPS/300 MSPS, 1.8 V Analog-to-Digital Converter
• Manufacturer: Analog Devices

Specifications of AD9211

• Resolution (bits): 10bit
• # Chan: 1
• Sample Rate: 300MSPS
• Interface: LVDS,Par
• Analog Input Type: Diff-Uni
• Ain Range: 1.25 V p-p
• Adc Architecture: Pipelined
• Pkg Type: CSP

THEORY OF OPERATION
The AD9211 architecture consists of a front-end sample and
hold amplifier (SHA) followed by a pipelined switched capacitor
ADC. The quantized outputs from each stage are combined into
a final 10-bit result in the digital correction logic. The pipelined
architecture permits the first stage to operate on a new input
sample, while the remaining stages operate on preceding
samples. Sampling occurs on the rising edge of the clock.
Each stage of the pipeline, excluding the last, consists of a low
resolution flash ADC connected to a switched capacitor DAC
and interstage residue amplifier (MDAC). The residue amplifier
magnifies the difference between the reconstructed DAC output
and the flash input for the next stage in the pipeline. One bit of
redundancy is used in each stage to facilitate digital correction
of flash errors. The last stage simply consists of a flash ADC.
The input stage contains a differential SHA that can be ac- or
dc-coupled in differential or single-ended mode. The output-
staging block aligns the data, carries out the error correction,
and passes the data to the output buffers. The output buffers are
powered from a separate supply, allowing adjustment of the
output voltage swing. During power-down, the output buffers
go into a high impedance state.
ANALOG INPUT AND VOLTAGE REFERENCE
The analog input to the AD9211 is a differential buffer. For best
dynamic performance, the source impedances driving VIN+
and VIN− should be matched such that common-mode settling
errors are symmetrical. The analog input is optimized to provide
superior wideband performance and requires that the analog
inputs be driven differentially. SNR and SINAD performance
degrades significantly if the analog input is driven with a single-
ended signal.
A wideband transformer, such as Mini-Circuits® ADT1-1WT,
can provide the differential analog inputs for applications that
require a single-ended-to-differential conversion. Both analog
inputs are self-biased by an on-chip resistor divider to a
nominal 1.3 V.
An internal differential voltage reference creates positive and
negative reference voltages that define the 1.25 V p-p fixed span
of the ADC core. This internal voltage reference can be adjusted
by means of SPI control. See the AD9211 Configuration Using
the SPI section for more details.
Differential Input Configurations
Optimum performance is achieved while driving the AD9211
in a differential input configuration. For baseband applications,
the
and a flexible interface to the ADC. The output common-mode
AD8138
differential driver provides excellent performance
Rev. 0 | Page 19 of 28
voltage of the AD8138 is easily set to AVDD/2 + 0.5 V, and the
driver can be configured in a Sallen-Key filter topology to
provide band limiting of the input signal.
At input frequencies in the second Nyquist zone and above, the
performance of most amplifiers may not be adequate to achieve
the true performance of the AD9211. This is especially true in
IF undersampling applications where frequencies in the 70 MHz
to 100 MHz range are being sampled. For these applications,
differential transformer coupling is the recommended input
configuration. The signal characteristics must be considered
when selecting a transformer. Most RF transformers saturate at
frequencies below a few MHz, and excessive signal power can
also cause core saturation, which leads to distortion.
In any configuration, the value of the shunt capacitor, C, is
dependent on the input frequency and may need to be reduced
or removed.
As an alternative to using a transformer-coupled input at
frequencies in the second Nyquist zone, the
driver can be used (see Figure 41).
ANALOG INPUT
ANALOG INPUT
1V p-p
Figure 39. Differential Input Configuration Using the AD8138
Figure 41. Differential Input Configuration Using the AD8352
Figure 40. Differential Transformer—Coupled Configuration
C
1.25V p-p
D
0.1µF
0.1µF
0.1µF
R
49.9Ω
D
0Ω
0Ω
R
G
16
1
2
3
4
5
499Ω
523Ω
50Ω
V
AD8352
CC
8, 13
14
0.1µF
0.1µF
AD8138
0.1µF
11
10
499Ω
499Ω
15Ω
15Ω
2pF
0.1µF
0.1µF
33Ω
33Ω
20pF
200Ω
200Ω
AD9211
VIN+
VIN–
AD8352
R
R
0.1µF
C
AD9211
VIN+
VIN–
AVDD
CML
AD9211
differential
AD9211
VIN+
VIN– CML