AD7676 Analog Devices, AD7676 Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7676
Manufacturer Part Number
AD7676
Description
Manufacturer
Analog Devices
Datasheet
1.AD7676.pdf
(20 pages)
Specifications of AD7676
Resolution (bits)
16bit
# Chan
1
Sample Rate
500kSPS
Interface
Par,Ser,SPI
Analog Input Type
Diff-Uni
Ain Range
(2Vref) p-p
Adc Architecture
SAR
Pkg Type
CSP,QFP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD7676AST
Manufacturer:
ADI
Quantity:
150
Company:
Part Number:
AD7676ASTZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD7676ASTZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7676ASTZRL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
External Clock Data Read During Conversion
Figure 20 shows the detailed timing diagrams of this method.
During a conversion, while both CS and RD are LOW, the result
of the previous conversion can be read. The data is shifted out,
MSB first, with 16 clock pulses, and is valid on both rising and
falling edges of the clock. The 16 bits have to be read before the
current conversion is complete. If that is not done, RDERROR is
pulsed HIGH and can be used to interrupt the host interface to
prevent incomplete data reading. There is no daisy chain feature
in this mode, and RDC/SDIN input should always be tied either
HIGH or LOW.
To reduce performance degradation due to digital activity, a fast
discontinuous clock of at least 18 MHz is recommended to ensure
that all the bits are read during the first half of the conversion
phase. For this reason, this mode is more difficult to use.
MICROPROCESSOR INTERFACING
The AD7676 is ideally suited for traditional dc measurement
applications supporting a microprocessor and ac signal processing
applications interfacing to a digital signal processor. The AD7676
is designed to interface either with a parallel 8-bit or 16-bit wide
REV. B
Figure 20. Slave Serial Data Timing for Reading (Read Previous Conversion during Conversion)
SDOUT
CNVST
BUSY
SCLK
CS
t
16
CNVST IN
t
3
SCLK IN
Figure 21. Two AD7676s in a Daisy Chain Configuration
CS IN
t
31
RDC/SDIN
X
t
36
1
AD7676
t
(UPSTREAM)
35
D15
t
37
BUSY
2
NO. 2
SDOUT
CNVST
D14
EXT/INT = 1
SCLK
t
32
CS
3
D13
–17–
interface or with a general-purpose Serial Port or I/O Ports on a
microcontroller. A variety of external buffers can be used with
the AD7676 to prevent digital noise from coupling into the ADC.
The following sections illustrate the use of the AD7676 with
an SPI-equipped microcontroller, and the ADSP-21065L and
ADSP-218x signal processors.
SPI Interface (MC68HC11)
Figure 22 shows an interface diagram between the AD7676 and an
SPI-equipped microcontroller, such as the MC68HC11. To accom-
modate the slower speed of the microcontroller, the AD7676 acts
as a slave device and data must be read after conversion. This mode
also allows the daisy chain feature. The convert command could
be initiated in response to an internal timer interrupt. The reading
of output data, one byte at a time if necessary, could be initiated
in response to the end-of-conversion signal (BUSY going LOW)
using an interrupt line of the microcontroller. The serial periph-
eral interface (SPI) on the MC68HC11 is configured for Master
Mode (MSTR) = 1, Clock Polarity Bit (CPOL) = 0, Clock Phase
Bit (CPHA) = 1, and SPI interrupt enable (SPIE) = 1 by writing
to the SPI Control Register (SPCR). The IRQ is configured for
edge-sensitive-only operation (IRQE = 1 in OPTION register).
RDC/SDIN
INVSCLK = 0
(DOWNSTREAM)
14
AD7676
BUSY
NO. 1
15
SDOUT
CNVST
SCLK
CS
D1
16
BUSY
OUT
RD = 0
DATA
OUT
D0
AD7676