AD7851 Analog Devices, AD7851 Datasheet - Page 14

• Manufacturer Part Number: AD7851
• Description: 14-Bit, 333 kSPS, Serial Sampling A/D Converter
• Manufacturer: Analog Devices

Specifications of AD7851

• Resolution (bits): 14bit
• # Chan: 1
• Sample Rate: 333kSPS
• Interface: Ser,SPI
• Analog Input Type: Diff-Uni
• Ain Range: (Vref) p-p,Uni (Vref)
• Adc Architecture: SAR
• Pkg Type: DIP,SOIC,SOP

AD7851
Adjusting the Offset Calibration Register
The offset calibration register contains 16 bits, 2 leading 0s, and
14 data bits. By changing the contents of the offset register, dif-
ferent amounts of offset on the analog input signal can be com-
pensated for. Increasing the number in the offset calibration
register compensates for the negative offset on the analog input
signal, and decreasing the number in the offset calibration regis-
ter compensates for the positive offset on the analog input signal.
The default value of the offset calibration register is approxi-
mately 0010 0000 0000 0000. This is not an exact value, but the
value in the offset register should be close to this value. Each of
the 14 data bits in the offset register is binary weighted; the MSB
has a weighting of 5% of the reference voltage, the MSB-1 has a
weighting of 2.5%, the MSB-2 has a weighting of 1.25%, and so
on down to the LSB which has a weighting of 0.0006%.
WRITE TO CONTROL REGISTER SETTING STCAL = 0, RDSLT1 = 1,
Figure 9. Flowchart for Reading from the
Calibration Registers
RDSLT0 = 0, AND CALSLT1, CALSLT0 = 00, 01, 10, 11
AUTOMATICALLY INCREMENTED
CAL REGISTER POINTER IS
CAL REGISTER POINTER IS
AUTOMATICALLY RESET
READ CAL REGISTER
OPERATION
REGISTER
FINISHED
ABORT
START
WRITE
LAST
OR
?
YES
NO
–14–
This gives a resolution of ± 0.0006% of V
More accurately the resolution is ± (0.05 × V
± 0.015 mV, with a 2.5 V reference. The maximum offset that
can be compensated for is ± 5% of the reference voltage, which
equates to ± 125 mV with a 2.5 V reference and ± 250 mV with
a 5 V reference.
Q. If a +20 mV offset is present in the analog input signal and
A. The 2.5 V reference implies that the resolution in the off-
This method of compensating for offset in the analog input signal
allows for fine-tuning the offset compensation. If the offset on the
analog input signal is known, there will be no need to apply the
offset voltage to the analog input pins to do a system calibration.
The offset compensation can take place in software.
Adjusting the Gain Calibration Register
The gain calibration register contains 16 bits, 2 leading 0s, and
14 data bits. The data bits are binary weighted as in the offset
calibration register. The gain register value is effectively multi-
plied by the analog input to scale the conversion result over the
full range. Increasing the gain register compensates for a
smaller analog input range and decreasing the gain register
compensates for a larger input range. The maximum analog
input range that the gain register can compensate for is 1.025
times the reference voltage, and the minimum input range is
0.975 times the reference voltage.
the reference voltage is 2.5 V, what code needs to be written
to the offset register to compensate for the offset?
set register is 5% × 2.5 V/2
0.015 mV = 1310.72; rounding to the nearest number gives
1311. In binary terms this is 0101 0001 1111, therefore
decrease the offset register by 0101 0001 1111.
13
= 0.015 mV. 20 mV/
REF
REF
approximately.
)/2
13
V =
REV. B