ADM1075 Analog Devices, ADM1075 Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
ADM1075
Manufacturer Part Number
ADM1075
Description
?48 V Hot Swap Controller and Digital Power Monitor with PMBus Interface
Manufacturer
Analog Devices
Datasheet
1.ADM1075.pdf
(52 pages)
Specifications of ADM1075
Uv & Ov Detection
OV pin,UVH pin,UVL pin
I Monitor Accuracy (+/-%)
1%
Other Inputs
CONV Pin,RESTARTb,SHDNb
Other Outputs
GPO1/ALERT1b/CONV,GPO2/ALERT2B,LATCHb,PWRGDb,SPLYGDb
Package
28 ld TSSOP,28-ld LFCSP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
ADM1075
timing cycle. The TIMER pin is pulled up with 3 μA. When the
TIMER reaches the V
of the initial cycle is complete. The 100 μA current source then
pulls down the TIMER pin until it reaches V
initial cycle duration is related to C
equation:
For example, a 470 nF capacitor results in a power-up delay of
approximately 160 ms. Provided the UV and OV detectors are
inactive when the initial timing cycle terminates, the device is
ready to start a hot swap operation.
When the voltage across the sense resistor reaches the circuit
breaker trip voltage, V
activated, and the gate begins to regulate the current at the current
limit. This initiates a ramp-up on the TIMER pin. If the sense
voltage falls below this circuit breaker trip voltage before the
TIMER pin reaches V
disabled, and the 2 μA pull-down is enabled.
The circuit breaker trip voltage is not the same as the hot swap
sense voltage current limit. There is a small circuit breaker
offset, V
time before the current reaches the defined current limit.
However, if the overcurrent condition is continuous and the
sense voltage remains above the circuit breaker trip voltage, the
60 μA pull-up remains active and the FET remains in regulation.
This allows the TIMER pin to reach V
GATE shutdown. The LATCH pin is pulled low immediately.
In latch-off mode, the TIMER pin is switched to the 2 μA pull-
down when it reaches the V
remains low. While the TIMER pin is being pulled down, the
hot swap controller is kept off and cannot be turned back on.
When the voltage on the TIMER pin goes below the V
threshold, the hot swap controller can be reenabled by toggling
the UVx pin or by using the PMBus OPERATION command to
toggle the ON bit from on to off and then on again.
HOT SWAP FAULT RETRY
The
With the default pin configuration, the part latches off after an
overcurrent fault and LATCH goes active low. This condition
can then be reset by either a power cycling event or a low signal
to either the SHDN input or RESTART input. It can also be
reset by toggling the UVx pin, using the PMBus operation
command or the PMBus power cycle command.
If the LATCH pin is connected to the SHDN pin, the part
makes seven attempts to hot swap before latching off. In this
mode, the part uses the TIMER pin to time a delay between
each attempt. In this way, a large load capacitance can be
charged using consecutive current limit periods.
ADM1075
t
INITIAL
CBOS
, which means that the timer actually starts a short
=
V
turns off the FET after an overcurrent fault.
TIMERH
3
TIMERH
μA
TIMERH
CB
×
C
, the 60 μA timer pull-up current is
TIMER
threshold (1.0 V), the first portion
TIMERH
(1.0 V), the 60 μA pull-up is
+
(
V
threshold. The LATCH pin
TIMER
TIMERH
TIMERH
by the following
−
and initiate the
100
V
TIMERL
TIMERL
μA
(0.05 V). The
)
×
C
TIMERL
TIMER
Rev. 0 | Page 24 of 52
The part can also be configured to autoretry an infinite number
of times with a 10 second cooling period between each retry.
Connecting LATCH to RESTART means that the part makes
one hot swap attempt between each cooling period. Connecting
LATCH to SHDN and GPO2/ ALERT2 to RESTART means
that the part makes seven hot swap attempts between each
cooling period.
The duty cycle of the automatic retry cycle is set by the ratio of
2 μA/60 μA, which approximates to being on ~4% of the time.
The value of the timer capacitor determines the on time of this
cycle, which is calculated as follows:
A 470 nF capacitor on the TIMER pin gives ~8 ms of on time
(for example, to meet 10 ms SOA), and ~220 ms off time.
FAST RESPONSE TO SEVERE OVERCURRENT
The
responds to severe overcurrent events such as short circuits.
Such an event may cause catastrophic damage if not controlled
very quickly. A fast response circuit ensures that the
detects an overcurrent event at approximately 150% of the normal
current limit (ISET) and responds and controls the current
within 1 μs in most cases. The severe overcurrent threshold
and glitch filter times are digitally programmable through the
PMBus. The threshold can be selected as 125%, 150%, 200%, or
225% of the normal current limit, and the glitch filter time can
be set to 200 ns, 900 ns, 10.7 μs, or 57 μs. This sets a maximum
response time of 300 ns, 950 ns, 13 μs, or 60 μs.
UV AND OV
The
(UV) and overvoltage (OV) conditions. The OV pin is con-
nected to the input of an internal voltage comparator, and its
voltage level is internally compared with a 1 V voltage reference.
The user can program the value of the OV hysteresis by varying
the top resistor of the resistor divider on the pin. This
impedance in combination with the 5 μA OV hysteresis current
(current turned on after OV trips) sets the OV hysteresis
voltage.
The UV detector is split into two separate pins, UVH and UVL.
The voltage on the UVH pin is compared internally to a 1 V
reference, whereas the UVL pin is compared to a 0.9 V reference.
Therefore, if the pins are tied together, the UV hysteresis is 100 mV.
The hysteresis can be adjusted by placing a resistor between
UVL and UVH.
Figure 50 illustrates the positive voltage monitoring input
connection. An external resistor network divides the supply
voltage for monitoring. An undervoltage event is detected when
ADM1075
ADM1075
t
t
OV
OV
ON
OFF
= V
= ( V
RISING
FALLING
TIMERH
TIMERH
=
features a very fast detection circuit that quickly
monitors the supply voltage for undervoltage
≈
OV
OV
× ( C
− V
THRESHOLD
RISING
TIMER
TIMERL
/60 μA)
−
) × ( C
(
×
R
TOP
R
TOP
TIMER
×
R
5
+
BOTTOM
μA
/2 μA)
R
BOTTOM
)
Data Sheet
ADM1075